Skip to content
Please enter a keyword to search

  • DIN EN 12261:2007-07

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    GAS METERS - TURBINE GAS METERS

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-09-2020

    Language(s):  English

    Published date:  01-01-2007

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Vorwort
    1 Abschnitt - 1 Anwendungsbereich
    2 Abschnitt - 3 Begriffe, Definitionen und Symbole
    3 Abschnitt - 4 Zählerklassifizierung
    4 Abschnitt - 5 Anforderungen an das metrologische
                     Betriebsverhalten
    5 Abschnitt - 6 Anforderungen an Konstruktion und
                     Werkstoffe
    6 Abschnitt - 7 Messwertausgang am Zähler
    7 Abschnitt - 8 Kennzeichnung
    8 Neuer Abschnitt - 9 Dokumentation
    9 Anhang E.3 -Anzeigefehler
    10 Neuer Anhang - Anhang ZA
    Anhang ZA (informativ) Zusammenhang zwischen dieser
                           Norm und den grundlegenden
                           Anforderungen der
                           EG-Messgeräterichtlinie 2004/22

    Abstract - (Show below) - (Hide below)

    Describes the measuring conditions, requirements and tests for the construction, performance and safety of class 1,0 axial and radial turbine gas meters with mechanical indicating devices, herein after referred to as a meter(s), having in-line pipe connections for gas flow measurement.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DIN 33800. (08/2002) DRAFT 2017 issued in August 2017. (08/2017)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN 30690-1:2016-04 CONSTRUCTION ELEMENTS IN THE GAS SUPPLY SYSTEM - PART 1: REQUIREMENTS FOR CONSTRUCTION ELEMENTS IN GAS SUPPLY SYSTEMS

    Standards Referencing This Book - (Show below) - (Hide below)

    OIML D 11 : 2013 GENERAL REQUIREMENTS FOR MEASURING INSTRUMENTS - ENVIRONMENTAL CONDITIONS
    EN 50020:2002 Electrical apparatus for potentially explosive atmospheres - Intrinsic safety 'i'
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
    EN 12405 : 2002 GAS METERS - GAS-VOLUME ELECTRONIC CONVERSION DEVICES
    EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
    EN 119000 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: DRY AND MERCURY WETTED REED CONTACT UNITS
    ISO/TR 5168:1998 Measurement of fluid flow Evaluation of uncertainties
    EN 60947-5-6:2000 Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR)
    EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
    EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
    EN 334:2005+A1:2009 Gas pressure regulators for inlet pressures up to 100 bar
    EN 10204:2004 Metallic products - Types of inspection documents
    ISO 9001:2015 Quality management systems — Requirements
    ISO 7005-1:2011 Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    EN 50014:1997/A2:1999 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - GENERAL REQUIREMENTS
    IEC 60947-5-6:1999 Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR)
    EN 60730-1:2016 Automatic electrical controls - Part 1: General requirements
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective