DIN EN 13598-1:2011-02
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
Hardcopy , PDF
English
01-01-2011
02-12-2020
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Abbreviations
4 Material
4.1 General
4.2 Sealing ring retaining components
4.3 Sealing rings
4.4 Adhesives for PVC-U
5 General characteristics
5.1 General
5.2 Assemblies
5.3 Colour
6 Geometrical characteristics
6.1 General
6.2 Dimensions
6.3 Additional requirements
7 Types of ancillary fittings
8 Physical characteristics
9 Mechanical characteristic
10 Performance requirements
11 Marking
11.1 General
11.2 Minimum required marking, ancillary fittings
11.3 Additional marking
Bibliography
This standard is included in DIN Handbook 13-6, 88 and 356.
| DocumentType |
Standard
|
| Pages |
25
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN 13598-1 : 2011 | Identical |
| NEN EN 13598-1 : 2010 | Identical |
| PREN 13598-1 : DRAFT 2010 | Identical |
| BS EN 13598-1:2010 | Identical |
| NS EN 13598-1 : 2010 | Identical |
| NBN EN 13598-1 : 2011 | Identical |
| I.S. EN 13598-1:2010 | Identical |
| NF EN 13598-1 : 2011 | Identical |
| EN 13598-1:2010 | Identical |
| UNE-EN 13598-1:2011 | Identical |
| DIN HDBK 88 : 11ED 2016 | ENTWAESSERUNGSKANALARBEITEN, DRUCKROHRLEITUNGSARBEITEN AUSSERHALB VON GEBAEUDEN, DRAEN- UND VERSICKERARBEITEN VOB/STLB-BAU - VOB TEIL C: ATV DIN 18299, ATV DIN 18306, ATV DIN 18307, ATV DIN 18308 |
| DIN HDBK 13-6 : 2ED 2013 | SCHAECHTE FUER ABWASSERLEITUNGEN UND -KANAELE, STRASSENENTWAESSERUNGSGEGENSTAENDE |
| DIN HDBK 356 : 1ED 2004 | ABWASSERTECHNIK 6 - SCHAECHTE FUER ABWASSERLEITUNGEN UND -KANAELE, STRASSENENTWAESSERUNGSGEGENSTAENDE |
| EN 1277:2003 | Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints |
| EN 295-3:2012 | Vitrified clay pipe systems for drains and sewers - Part 3: Test methods |
| ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| ISO 265-1:1988 | Pipes and fittings of plastics materials — Fittings for domestic and industrial waste pipes — Basic dimensions: Metric series — Part 1: Unplasticized poly(vinyl chloride) (PVC-U) |
| EN 1055:1996 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling |
| EN 14680:2015 | Adhesives for non-pressure thermoplastics piping systems - Specifications |
| EN 922:1994 | Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the K-value |
| EN 1253-2:2015 | Gullies for buildings - Part 2: Roof drains and floor gullies without trap |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| EN 476:2011 | General requirements for components used in drains and sewers |
| EN 14982:2006+A1:2010 | Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness |
| EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| EN 12666-1:2005+A1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| ISO 1183-2:2004 | Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method |
| EN ISO 580:2005 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) |
| EN 1401-1:2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 14830:2006 | Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance |
| EN 1053:1995 | Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| EN 1253-1:2015 | Gullies for buildings - Part 1: Trapped floor gullies with a depth water seal of at least 50 mm |
| EN 1437:2002 | Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading |
| EN 12256:1998 | Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| EN ISO 1183-2:2004 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004) |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.