Skip to content
Please enter a keyword to search

  • DIN EN 14364:2013-05

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-08-2023

    Language(s):  English, German

    Published date:  01-05-2013

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
    4 General requirements
    5 Pipes
    6 Fittings
    7 Joint performance
    Annex A (normative) - Test method for the resistance
            to bending and pressure of end-thrust loaded
            joints in pipe systems
    Bibliography

    Abstract - (Show below) - (Hide below)

    This standard is included in DIN Handbook 171, 13-5 and 259.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DIN EN 1115-2. (05/2002) Supersedes DIN 19565-1, DIN 19565-1 E, DIN EN 1115-1, DIN EN 1115-1 E, DIN EN 1115-3, DIN EN 1115-3 E, DIN EN 1115-5, DIN EN 1115-5 E, DIN EN 1636-3, DIN EN 1636-3 E, DIN EN 1636-5 and DIN EN 1636-5 E. (07/2006)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN HDBK 13-5 : 5ED 2015 ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN
    DIN HDBK 259 : 4ED 2007 ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN
    DIN 16869-2:2014-12 CENTRIFUGALLY CAST FILLED GLASS FIBRE REINFORCED UNSATURATED POLYESTER RESIN (UP-GF) PIPES - PART 2: GENERAL QUALITY REQUIREMENTS, TESTING
    DIN 1986-4:2019-08 DRAINAGE SYSTEMS ON PRIVATE GROUND - PART 4: FIELDS OF APPLICATION OF SEWAGE PIPES AND FITTINGS OF DIFFERENT MATERIALS
    DIN 16869-1:2014-12 CENTRIFUGALLY CAST FILLED GLASS FIBRE REINFORCED UNSATURATED POLYESTER RESIN (UP-GF) PIPES - PART 1: DIMENSIONS
    DIN HDBK 171 : 5ED 2015 ROHRE, ROHRLEITUNGSTEILE UND ROHRVERBINDUNGEN AUS REAKTIONSHARZFORMSTOFFEN
    DIN 1986-4:2011-12 DRAINAGE SYSTEMS ON PRIVATE GROUND - PART 4: FIELDS OF APPLICATION OF SEWAGE PIPES AND FITTINGS OF DIFFERENT MATERIALS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 8521:2009 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength
    EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
    ISO 7432:2002 Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
    EN ISO 2078:1994/A1:2015 TEXTILE GLASS - YARNS - DESIGNATION (ISO 2078:1993/AMD 1:2015)
    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
    EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
    ISO/TR 10465-3:2007 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 3: Installation parameters and application limits
    ISO 10928:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
    ISO 1452-3:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 3: Fittings
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    CEN/TS 14632:2012 Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
    EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
    ISO 527-5:2009 Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
    EN 1447:2009+A1:2010 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
    EN 476:2011 General requirements for components used in drains and sewers
    ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints
    ISO 2078:1993 Textile glass Yarns Designation
    ISO 8483:2003 Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of bolted flange joints
    ISO 8513:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
    ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
    ISO 4200:1991 Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
    ISO 10466:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method to prove the resistance to initial ring deflection
    ISO 10471:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
    EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
    EN 1119:2009 Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements
    EN ISO 1452-3:2010 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings (ISO 1452-3:2009, corrected version 2010-03-01)
    ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
    CEN/TS 14807:2013 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines
    ISO 2531:2009 Ductile iron pipes, fittings, accessories and their joints for water applications
    CEN/TS 14578:2013 Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective