Skip to content
Please enter a keyword to search

  • DIN EN 215:2007-11

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    THERMOSTATIC RADIATOR VALVES - REQUIREMENTS AND TEST METHODS

    Available format(s):  Hardcopy, PDF

    Superseded date:  21-09-2018

    Language(s):  English

    Published date:  01-01-2007

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Vorwort
    Vorwort der Änderung A1
    1 Anwendungsbereich
    2 Normative Verweisungen
    3 Begriffe
      3.1 Heizkörperventil - Bauteile (siehe Bild 1)
      3.2 Bauarten von Thermostatköpfen (siehe Bild 3)
      3.3 Ausführungen von Anschlüssen
      3.4 Betriebsverhalten
      3.5 Technische Begriffe
    4 Formelzeichen und Abkürzungen
    5 Anforderungen
      5.1 Masse
      5.2 Mechanische Eigenschaften
      5.3 Betriebsverhalten
      5.4 Dauer- und Temperaturbeständigkeit
    6 Prüfverfahren
      6.1 Prüfeinrichtungen
      6.2 Kennlinien von Thermostatventilen
      6.3 Prüfung der mechanischen Eigenschaften
      6.4 Prüfung des Betriebsverhaltens
      6.5 Plan für die Durchführung der Prüfungen
    7 Vom Hersteller zu liefernde technische Angaben
    Anhang A (normativ) Thermostatische Heizkörperventile; Masse
                          und Ausführungen des Anschlusses
                          A.1 Allgemeines
                          A.2 Masse
                          A.3 Ausführungen des Anschlusses
                          A.4 Werkstoffe für Gehäuse, Tülle und Nut
                          A.5 Bezeichnung
                          A.6 Kennzeichnung (Diese Kennzeichnung
                              gilt nicht für mögliche
                              Zertifizierungskennzeichnung)
    Anhang B (informativ) Turbulenzgrad der Luftströmung im Raum
    Anhang C (informativ) Prüfnormal für integrierte Thermostatventile
    Literaturhinweise

    Abstract - (Show below) - (Hide below)

    Specifies definitions, requirements and test methods for thermostatic radiator valves. Applies to two port thermostatic valves with or without pre-setting facility for fitting to radiators in wet central heating installations up to a water temperature of 120 degrees C and a nominal pressure of PN 10.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DIN 3841-1 and DIN EN 215-1. (09/2004) DRAFT 2017 issued in February 2017. (02/2017)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    VDI 2073 Blatt 2:2012-05 Hydraulic systems in building services - Hydraulic balancing
    VDI/VDE 3512 Blatt 4:2017-03 Temperature measurement for building automation - Testing of temperature sensors

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 12168:2016 Copper and copper alloys - Hollow rod for free machining purposes
    EN 12166:2016 Copper and copper alloys - Wire for general purposes
    EN 12167:2016 COPPER AND COPPER ALLOYS - PROFILES AND BARS FOR GENERAL PURPOSES
    ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
    EN 12449:2016 Copper and copper alloys - Seamless, round tubes for general purposes
    EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
    EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
    ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
    EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
    ISO 965-1:2013 ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
    EN 12420:2014 Copper and copper alloys - Forgings
    EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
    EN 1982:2017 Copper and copper alloys - Ingots and castings
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective