DIN EN 556-2:2015-11
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Sterilization of medical devices - Requirements for medical devices to be designated \"STERILE\" - Part 2: Requirements for aseptically processed medical devices
Available format(s)
Hardcopy , PDF
Language(s)
German, English
Published date
01-11-2015
Superseded date
01-01-2025
Superseded by
€93.83
Excluding VAT
National foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 90/385/EEC on
active implantable medical devices
Annex ZB (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 93/42/EEC on
medical devices
Annex ZC (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 98/79/EC on in
vitro diagnostic medical devices
Bibliography
This standard is included in DIN HDBK 263, 406and 268.
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 556-2 : 2015 | Identical |
| EN 556-2:2015 | Identical |
| NEN EN 556-2 : 2015 | Identical |
| BS EN 556-2:2015 | Identical |
| NS EN 556-2 : 2003 | Identical |
| NF EN 556-2 : 2015 | Identical |
| I.S. EN 556-2:2015 | Identical |
| ONORM EN 556-2 : 2015 | Identical |
| UNE-EN 556-2:2016 | Identical |
| DIN HDBK 406 : 2ED 2016 | |
| DIN HDBK 263 : 4ED 2014 | |
| DIN HDBK 268 : 3ED 2015 | NICHT AKTIVE MEDIZINPRODUKTE - HORIZONTALE, HARMONISIERTE EUROPAEISCHE NORMEN GEMAESS EU-RICHTLINIEN AUF DEM GEBIET DER MEDIZIN |
| ISO 13408-4:2005 | Aseptic processing of health care products — Part 4: Clean-in-place technologies |
| EN ISO 11737-2:2009 | Sterilization of medical devices - Microbiological methods - Part 2: Tests of sterility performed in the definition, validation and maintenance of a sterilization process (ISO 11737-2:2009) |
| ISO 11137-1:2006 | Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 13408-7:2012 | Aseptic processing of health care products — Part 7: Alternative processes for medical devices and combination products |
| EN ISO 14937:2009 | Sterilization of health care products - General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices (ISO 14937:2009) |
| ISO 14160:2011 | Sterilization of health care products — Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives — Requirements for characterization, development, validation and routine control of a sterilization process for medical devices |
| EN ISO 13408-3:2011 | Aseptic processing of health care products - Part 3: Lyophilization (ISO 13408-3:2006) |
| EN ISO 13408-4:2011 | Aseptic processing of health care products - Part 4: Clean-in-place technologies (ISO 13408-4:2005) |
| ISO 11135:2014 | Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices |
| EN ISO 13408-5:2011 | Aseptic processing of health care products - Part 5: Sterilization in place (ISO 13408-5:2006) |
| ISO 13408-2:2003 | Aseptic processing of health care products — Part 2: Filtration |
| ISO 11737-2:2009 | Sterilization of medical devices — Microbiological methods — Part 2: Tests of sterility performed in the definition, validation and maintenance of a sterilization process |
| ISO 11737-1:2006 | Sterilization of medical devices — Microbiological methods — Part 1: Determination of a population of microorganisms on products |
| ISO/TS 17665-2:2009 | Sterilization of health care products — Moist heat — Part 2: Guidance on the application of ISO 17665-1 |
| EN ISO 13408-1:2015 | Aseptic processing of health care products - Part 1: General requirements (ISO 13408-1:2008, including Amd 1:2013) |
| ISO 13485:2016 | Medical devices — Quality management systems — Requirements for regulatory purposes |
| ISO 14937:2009 | Sterilization of health care products — General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| ISO 25424:2009 | Sterilization of medical devices — Low temperature steam and formaldehyde — Requirements for development, validation and routine control of a sterilization process for medical devices |
| CEN ISO/TS 17665-2:2009 | Sterilization of health care products - Moist heat - Part 2: Guidance on the application of ISO 17665-1 (ISO/TS 17665-2:2009) |
| EN ISO 11135:2014 | Sterilization of health-care products - Ethylene oxide - Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 11135:2014) |
| ISO 13408-3:2006 | Aseptic processing of health care products — Part 3: Lyophilization |
| EN ISO 25424:2011 | Sterilization of medical devices - Low temperature steam and formaldehyde - Requirements for development, validation and routine control of a sterilization process for medical devices (ISO 25424:2009) |
| EN ISO 11137-2:2015 | Sterilization of health care products - Radiation - Part 2: Establishing the sterilization dose (ISO 11137-2:2013) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 13408-1:2008 | Aseptic processing of health care products — Part 1: General requirements |
| ISO 20857:2010 | Sterilization of health care products — Dry heat — Requirements for the development, validation and routine control of a sterilization process for medical devices |
| ISO/TS 11139:2006 | Sterilization of health care products — Vocabulary |
| ISO 11137-3:2017 | Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control |
| ISO 11137-2:2013 | Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 11137-1:2015 | Sterilization of health care products - Radiation - Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices (ISO 11137-1:2006, including Amd 1:2013) |
| EN ISO 14971:2012 | Medical devices - Application of risk management to medical devices (ISO 14971:2007, Corrected version 2007-10-01) |
| EN ISO 17665-1:2006 | Sterilization of health care products - Moist heat - Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 17665-1:2006) |
| ISO 14971:2007 | Medical devices — Application of risk management to medical devices |
| EN ISO 20857:2013 | Sterilization of health care products - Dry heat - Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 20857:2010) |
| ISO 13408-6:2005 | Aseptic processing of health care products — Part 6: Isolator systems |
| ISO 15223-1:2016 | Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Part 1: General requirements |
| ISO 17664:2017 | Processing of health care products — Information to be provided by the medical device manufacturer for the processing of medical devices |
| EN ISO 11137-3:2017 | Sterilization of health care products - Radiation - Part 3: Guidance on dosimetric aspects of development, validation and routine control (ISO 11137-3:2017) |
| EN ISO 14160:2011 | Sterilization of health care products - Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives - Requirements for characterization, development, validation and routine control of a sterilization process for medical devices (ISO 14160:2011) |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
| ISO 13408-5:2006 | Aseptic processing of health care products — Part 5: Sterilization in place |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.