DIN EN 60112 : 2010

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS

Available format(s):

Superseded date: 08-11-2022

Language(s):

Published date: 12-01-2013

Publisher: Verband Deutscher Elektrotechniker

Table of Contents - (Show below) - (Hide below)

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Test specimen
6 Test specimen conditioning
   6.1 Environmental conditioning
   6.2 Test specimen surface state
7 Test apparatus
   7.1 Electrodes
   7.2 Test circuit
   7.3 Test solutions
   7.4 Dropping device
   7.5 Test specimen support platform
   7.6 Electrode assembly installation
8 Basic test procedure
   8.1 General
   8.2 Preparation
   8.3 Test procedure
9 Determination of erosion
10 Determination of proof tracking index (PTI)
   10.1 Procedure
   10.2 Report
11 Determination of comparative tracking index (CTI)
   11.1 General
   11.2 Determination of the 100 drop point
   11.3 Determination of the maximum 50 drop withstand voltage
   11.4 Report
Annex A (informative) List of factors that should be considered by
        product committees
Annex B (informative) Electrode material selection
Annex ZA (normative) Normative references to international
         publications with their corresponding European publications
Bibliography

Abstract - (Show below) - (Hide below)

Diese Internationale Norm legt das Verfahren zur Bestimmung der Prüfzahl und der Vergleichszahl der Kriechwegbildung an festen Isolierstoffen unter der Verwendung von Wechselspannung fest, und zwar an Materialproben, die aus Bauteilen entnommen wurden, und an Materialplatten.

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes DIN IEC 15E-122-CD, DIN IEC 60112 and DIN VDE 0303-1. (12/2003) DRAFT 2016 issued in October 2016. (10/2016)
Document Type	Standard
ISBN
Pages
Published
Publisher	Verband Deutscher Elektrotechniker
Status	Superseded
Superseded By	DIN EN IEC 60112:2022-11
Supersedes	DIN VDE 0303-1 : 1984 DIN IEC 60112 : 1984

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
NF EN 60112 : 2003 AMD 1 2010	Identical
IEC 60112:2003+AMD1:2009 CSV	Identical
I.S. EN 60112:2003	Identical
VDE 0303-11 : 2010	Corresponds
EN 60112 : 2003 AMD 1 2009	Identical
SN EN 60112 : 2003	Identical
BS EN 60112 : 2003	Identical
NBN EN 60112 : 2003 AMD 1 2010	Identical
UNE-EN 60112:2003	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

DIN EN ISO 16396-2:2017-07	Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017)
DIN EN ISO 25137-2 E : 2017	PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009)
DIN EN ISO 20753 E : 2014	PLASTICS - TEST SPECIMENS (ISO 20753:2008)
DIN EN ISO 20753:2014-07	PLASTICS - TEST SPECIMENS (ISO 20753:2008)
DIN EN ISO 3673-2 E : 2012	PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012)
DIN EN ISO 1872-2:2000-12	PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
DIN EN 81-2:2000-05	SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 2: HYDRAULIC LIFTS
DIN EN ISO 20028-2 E : 2017	PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017)
DIN EN ISO 19069-2:2016-07	PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016)
DIN EN ISO 17855-2 E : 2016	PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016)
DIN EN ISO 1874-2:2013-03	PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012)
DIN EN ISO 8986-2 E : 2010	PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
DIN EN ISO 3673-2:2012-10	Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012)
DIN EN ISO 16396-2 E : 2017	PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017)
DIN EN ISO 20028-2:2015-08 (Draft)	PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017)
DIN EN ISO 11542-2:2010-01	Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998 + Cor. 1:2007) (includes Corrigendum AC:2008)
DIN EN ISO 14910-2 E : 2013	PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
DIN EN 81-2:2010-08	SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 2: HYDRAULIC LIFTS
DIN EN ISO 17855-2:2016-06	PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016)
DIN EN ISO 19069-2 E : 2016	PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016)
DIN EN ISO 25137-2:2016-08 (Draft)	PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009)
DIN EN ISO 7792-2:2013-03	PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012)
DIN EN ISO 14910-2:2013-06	PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
DIN EN 81-1:2010-06	SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 1: ELECTRIC LIFTS
DIN EN 81-1:2000-05	SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 1: ELECTRIC LIFTS
DIN EN ISO 8986-2:2010-04	PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart