DIN EN 60249-1:1994-05

Withdrawn

Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

BASE MATERIALS FOR PRINTED CIRCUITS - PART 1: TEST METHODS

Available format(s):

Withdrawn date: 30-11-2009

Language(s):

Published date: 12-01-2013

Publisher: German Institute for Standardisation (Deutsches Institut für Normung)

Table of Contents - (Show below) - (Hide below)

Einleitung
Anwendungsbereich
Abschnitt
1 Allgemeines
  1.1 Normalklimate
  1.2 Genauigkeit von Zeiten und Messungen
  1.3 Probekörper
2 Elektrische Prüfungen
  2.0 Vorsichtsmassnahmen bei bestimmten
       elektrischen Prüfungen
  2.1 Widerstand der Metallfolie
  2.2 Oberflächenwiderstand nach Lagerung
       in feuchter Wärme, konstant
  2.3 Spezifischer Durchgangswiderstand nach
       Lagerung in feuchter Wärme, konstant
  2.4 Oberflächenkorrosion
  2.5 Kantenkorrosion
  2.6 Vergleichszahl der Kriechwegbildung
  2.7 Permittivitätszahl und Verlustfaktor
       nach feuchter Wärme und Nachbehandlung
  2.8 Durchschlagfestigkeit senkrecht zur Tafelebene
  2.9 Isolationseigenschaften bei erhöhter Temperatur
3 Nichtelektrische Prüfungen an metallkaschierten
  Materialien
  3.1 Wölbung
  3.2 Wölbung nach Ätzen und Wärmebehandlung
  3.3 Verwindung
  3.4 Verwindung nach Ätzen und Wärmebehandlung
  3.5 Abreisskraft
  3.6 Abschälkraft
  3.7 Blasenbildung nach Wärmeschock
  3.8 Stanzen und maschinelle Bearbeitung
  3.9 Oberflächenbeschaffenheit
  3.10 entfällt
  3.11 Dimensionsstabilität
  3.12 Beständigkeit gegen Biegewechselbeanspruchung
  3.13 Masse je Flächeneinheit der Metallfolie
       nach dem Laminieren (durch Ätzen)
  3.14 Dicke
  3.15 Rechtwinkligkeit von Zuschnitten
4 Nichtelektrische Prüfungen am Basismaterial
  4.1 Biegefestigkeit
  4.2 Measling
  4.3 Brennbarkeit
  4.4 Wasseraufnahme
  4.5 Linearer thermischer Ausdehnungskoeffizient
       Bilder

Abstract - (Show below) - (Hide below)

Specifies methods for testing electrical, mechanical and other properties of base materials in sheet or roll form for printed circuits irrespective of the nature of the insulating base material.

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes DIN IEC 60249-1 (05/2002)
Document Type	Standard
ISBN
Pages
Published
Publisher	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Withdrawn
Supersedes	DIN IEC 60249-1 : 1986

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
NF EN 60249-1 : 1995	Identical
BS EN 60249-1:1993	Identical
EN 60249-1 : 1993 COR 1994	Identical
SN EN 60249-1 : 1993 AMD 4 1994	Identical
I.S. EN 60249-1:1994	Identical
NBN EN 60249-1 : 1995	Identical
UNE-EN 60249-1:1997	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

DIN EN 60924 : 1994	D.C. SUPPLIED ELECTRONIC BALLASTS FOR TUBULAR FLUORESCENT LAMPS - GENERAL AND SAFETY REQUIREMENTS
DIN EN 60926 : 2000	AUXILIARIES FOR LAMPS - STARTING DEVICES (OTHER THAN GLOW STARTERS) - GENERAL AND SAFETY REQUIREMENTS
VDE 0712-14 : 2000	AUXILIARIES FOR LAMPS - STARTING DEVICES (OTHER THAN GLOW STARTERS) - GENERAL AND SAFETY REQUIREMENTS
DIN EN 60922 : 1997	AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - GENERAL AND SAFETY REQUIREMENTS
VDE 0882 : 1996	SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
DIN EN 61249-3-3:1999-11	MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES - PART 3-3: SECTIONAL SPECIFICATION SET FOR REINFORCED BASE MATERIALS, CLAD AND UNCLAD (INTENDED FOR FLEXIBLE PRINTED BOARDS); ADHESIVE COATED FLEXIBLE POLYESTER FILM
DIN EN 61046 : 1995 AMD 1 1997	D.C. OR A.C. SUPPLIED ELECTRONIC STEP-DOWN CONVERTORS FOR FILAMENT LAMPS - GENERAL AND SAFETY REQUIREMENTS
VDE 0712-12 : 1997	AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - GENERAL AND SAFETY REQUIREMENTS
DIN EN 60491 : 1996	SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
VDE 0712-20 : 1994	D.C. SUPPLIED ELECTRONIC BALLASTS FOR TUBULAR FLUORESCENT LAMPS - GENERAL AND SAFETY REQUIREMENTS

Standards Referencing This Book - (Show below) - (Hide below)

DIN IEC 60068-2-20:1991-04	ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TEST T: SOLDERING
ISO 565:1990	Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
DIN IEC 60194:1992-11	PRINTED CIRCUITS; TERMS AND DEFINITION
DIN IEC 60068-1:1990-11	ELECTRICAL ENGINEERING - BASIC ENVIRONMENTAL TESTING PROCEDURES - GENERAL AND GUIDANCE
ISO 4046:1978	Paper, board, pulp and related terms — Vocabulary
DIN VDE 0303-6 : 1968	SPECIFICATION FOR ELECTRICAL TESTS OF INSULATING MATERIALS - DETERMINATION OF ELECTROLYTIC CORROSIVE EFFECTS
ISO 62:2008	Plastics Determination of water absorption
DIN IEC 60068-2-2:1980-03	BASIC ENVIRONMENTAL TESTING PROCEDURES; TESTS; TESTS B: DRY HEAT
DIN VDE 0303-1 : 1984	METHOD FOR DETERMINING THE COMPARATIVE AND THE PROOF TRACKING INDICES OF SOLID INSULATING MATERIALS UNDER MOIST CONDITIONS
ISO 178:2010	Plastics Determination of flexural properties

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart