DIN EN 88:1996-08
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PRESSURE GOVERNORS FOR GAS APPLIANCES FOR INLET PRESSURES UP TO 200 MBAR
01-04-2008
12-01-2013
1 Allgemeines
1.1 Zweck und Anwendungsbereich
1.2 Normative Verweisungen
1.3 Begriffe
1.4 Einteilung
1.5 Messgrössen
2 Bauanforderungen
2.1 Allgemeine Bauanforderungen
2.2 Werkstoffe
2.3 Anschlüsse
2.4 Abdichten von Durchführungen beweglicher Teile
2.5 Druckmessstutzen
3 Funktionsanforderungen
3.1 Allgemeines
3.2 Ausserbetriebsetzen des Reglers
3.3 Äussere Dichtheit
3.4 Torsion und Biegung
3.5 Beständigkeit
3.6 Regelverhalten
3.7 Betriebsgeräusch
3.8 Langzeitstabilität des Regelverhaltens
3.9 Schliessdruck
4 Prüfverfahren
4.1 Allgemeines
4.2 Ausserbetriebsetzen des Reglers
4.3 Äussere Dichtheit
4.4 Torsion und Biegung
4.5 Beständigkeit
4.6 Regelverhalten
4.7 Betriebsgeräusch
4.8 Langzeitstabilität des Regelverhaltens
4.9 Schliessdruck
5 Kennzeichnung, Einbau- und Betriebsanleitung
5.1 Kennzeichnung
5.2 Anleitungen für Einbau, Betrieb und Wartung
5.3 Warnhinweis
Anhang A (informativ) Hinweis auf die Überein-stimmung mit
den grundlegenden Anfor-derungen der
EG-Gasgeräterichtlinie
Anhang B (informativ) Typische Regler und Reglerteile
Anhang C (informativ) Verwendung von Gewindennach ISO 7-1:1982
und ISO 228-1: 1982
Anhang D (normativ) Dichtheitsprüfung - volume-trisches
Verfahren
Anhang E (normativ) Dichtheitsprüfung - Druck-abfallverfahren
Anhang F (normativ) Umrechnung des Druckabfalls in Leckrate
Anhang G (informativ) Zusammenstellung der Anforderungen und
Prüfschritte
This standard is included in DIN Handbook 130. Describes the safety, constructional and performance requirements for pressure governors for use with gas appliances. Gives test procedures for evaluating these and information necessary for the purchaser and user. Applies to pressure governors for gas-burning appliances of connection size up to and including DN 50 and that may be used and tested independently of these appliances. Suitable for fuel gases of the 1st, 2nd and 3rd families. Does not cover: governors connected to mains and governors for gas appliances installed out-of-doors.
| DevelopmentNote |
Supersedes DIN 3392. (02/2003)
|
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN 88 : 1993 AMD 1 1997 | Identical |
| NEN EN 88 : 1992 AMD 1 1996 | Identical |
| SN EN 88 : 1997 AMD 1 1997 | Identical |
| NF EN 88 : 91 AMD 1 96 | Identical |
| NS EN 88 : 1991 AMD 1 1996 | Identical |
| I.S. EN 88:1992 | Identical |
| BS EN 88:1991 | Identical |
| EN 88:1991/A1:1996 | Identical |
| ISO 274:1975 | Copper tubes of circular section — Dimensions |
| DIN 1754-1:1969-08 | COPPER TUBES - SEAMLESS DRAWN, DIMENSION RANGES AND COORDINATION OF TOLERANCES |
| DIN 1786:1980-05 | SEAMLESS DRAWN COPPER TUBES FOR PIPING SYSTEMS |
| DIN EN 60730-1:2017-05 | AUTOMATIC ELECTRICAL CONTROLS - PART 1: GENERAL REQUIREMENTS (IEC 60730-1:2013, MODIFIED + COR1:2014) |
| DIN 13-13:1983-10 | ISO METRIC SCREW THREADS - SELECTED SIZES FOR SCREWS, BOLTS AND NUTS FROM 1 TO 52 MM SCREW THREAD DIAMETER AND LIMITS OF SIZES |
| DIN ISO 228-1:1994-12 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
| DIN 2999-1:1983-07 | PIPE THREADS FOR TUBES AND FITTINGS - PARALLEL INTERNAL THREAD AND TAPER EXTERNAL THREAD - TREAD DIMENSIONS |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| DIN 6630:1985-08 | PACKAGING SCREW THREADS FOR SCREWING UP PROFILES; DESIGN PROFILES AND SIZES |
| ISO 65:1981 | Carbon steel tubes suitable for screwing in accordance with ISO 7-1 |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.