DIN EN ISO 11297-3:2013-11
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013)
Hardcopy , PDF
German, English
01-01-2013
04-05-2019
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings at the 'M' stage
7 Ancillary components
8 Fitness for purpose of the installed lining
system at the 'I' stage
9 Installation practice
Annex A (normative) - Factory-folded heat-reverted
polyethylene (PE) pipe - Determination of
memory ability
Bibliography
Describes requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure.
| DevelopmentNote |
DRAFT 2017 issued in September 2017. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 11297-3:2013 | Identical |
| ISO 11297-3:2018 | Identical |
| PREN ISO 11297-3 : DRAFT 2012 | Identical |
| DIN EN ISO 11297-1:2013-08 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 1: GENERAL (ISO 11297-1:2013) |
| DIN EN ISO 9967:2016-07 | THERMOPLASTICS PIPES - DETERMINATION OF CREEP RATIO (ISO 9967:2016) |
| EN 12201-4:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
| ISO 4427-3:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings |
| ISO 8772:2006 | Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene (PE) |
| ISO 4427-1:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| DIN EN ISO 11295:2016-08 (Draft) | CLASSIFICATION AND INFORMATION ON DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers — Series of preferred numbers |
| ISO 4427-5:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system |
| DIN EN ISO 11297-1:2013-08 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 1: GENERAL (ISO 11297-1:2013) |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 9967:2016 | Thermoplastics pipes — Determination of creep ratio |
| ISO 11297-1:2013 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 1: General |
| ISO 4427-2:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.