Skip to content
Please enter a keyword to search

  • DIN EN ISO 14978:2006-09

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-05-2019

    Language(s): 

    Published date:  01-01-2006

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Abbreviations
    5 Design characteristics
      5.1 General
      5.2 Indicating measuring equipment
      5.3 Material measures
    6 Metrological characteristics
      6.1 General
      6.2 Identification, definition and choice of metrological
          characteristics
      6.3 Indicating measuring equipment - identification of
          general metrological characteristics
      6.4 Material measures - Identification of general
          metrological characteristics
    7 Types of presentation and types of specifications for
      characteristics
      7.1 General
      7.2 Presentation of characteristic curves - Fixed and
          floating zero
      7.3 Presentation of a characteristic - Statistical
      7.4 Specifications for single-value metrological
          characteristics
      7.5 Specification for metrological characteristics
          defined in a range
      7.6 Specification for metrological characteristics defined
          in a two- or three-dimensional range
    8 Calibration of metrological characteristics
      8.1 Manufacturer and supplier of measuring instruments
      8.2 User of measuring instruments
      8.3 Measurement uncertainty
    9 Marking
    Annex A (normative) General minimum requirements and
            guidance for clauses in GPS standards for
            specific measuring equipment
    Annex B (informative) Data sheet for measuring equipment
            requirements
    Annex C (normative) Relation to the GPS matrix model
    Bibliography

    Abstract - (Show below) - (Hide below)

    This standard is included in DIN Handbook 11-1 and 11-3. Describes the general requirements, terms and definitions of characteristics of simple GPS measuring equipment, e.g. micrometers, dial gauges, callipers, surface plates, height gauges, gauge blocks, but not necessarily excluding more complicated equipment.

    General Product Information - (Show below) - (Hide below)

    Development Note DRAFT 2017 issued in March 2017. (03/2017)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN 863-1:2016-07 (Draft) GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - MICROMETERS - PART 1: MICROMETERS FOR EXTERNAL MEASUREMENTS; MAXIMUM PERMISSIBLE ERRORS
    DIN EN ISO 463 : 2009-07 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - DESIGN AND METROLOGICAL CHARACTERISTICS OF MECHANICAL DIAL GAUGES
    DIN EN ISO 1938-1:2016-03 Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Plain limit gauges of linear size (ISO 1938-1:2015)
    DIN HDBK 303 : 2ED 2008
    DIN EN ISO 8015:2011-09 Geometrical product specifications (GPS) - Fundamentals - Concepts, principles and rules (ISO 8015:2011)
    DIN EN ISO 13385-1:2011-12 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 1: CALLIPERS; DESIGN AND METROLOGICAL CHARACTERISTICS (ISO 13385-1:2011)
    DIN EN ISO 25178-605:2014-06 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: AREAL - PART 605: NOMINAL CHARACTERISTICS OF NON-CONTACT (POINT AUTOFOCUS PROBE) INSTRUMENTS (ISO 25178-605:2014)
    VDI/VDE/DGQ 2618 Blatt 7.2:2008-07 Inspection of measuring and test equipment - Test instruction for protractors
    VDI/VDE 3699 Blatt 1:2015-04 Process control using display screens - Terminology
    DIN EN ISO 13225:2012-08 Geometrical product specifications (GPS) - Dimensional measuring equipment; Height gauges - Design and metrological characteristics (ISO 13225:2012)
    DIN HDBK 11-3 : 12ED 2017 LAENGENPRUEFTECHNIK 3 - MESSGERAETE UND MESSVERFAHREN FUER DIE LAENGENPRUEFTECHNIK
    DIN EN ISO 25178-70:2014-06 GEOMETRICAL PRODUCT SPECIFICATION (GPS) - SURFACE TEXTURE: AREAL - PART 70: MATERIAL MEASURES (ISO 25178-70:2014)
    DIN EN ISO 13102:2012-12 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT: ELECTRONIC DIGITAL-INDICATOR GAUGE - DESIGN AND METROLOGICAL CHARACTERISTICS (ISO 13102:2012)
    DIN HDBK 11-1 : 4ED 2016
    DIN EN ISO 14253-3:2011-10 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO 14253-3:2011)
    DIN EN ISO 463 E : 2006 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - DESIGN AND METROLOGICAL CHARACTERISTICS OF MECHANICAL DIAL GAUGES
    DIN EN ISO 1938-2:2017-05 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 2: REFERENCE DISK GAUGES (ISO 1938-2:2017)
    DIN EN ISO 17450-2:2013-04 Geometrical product specifications (GPS) - General concepts - Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities (ISO 17450-2:2012)
    DIN EN ISO 13385-2:2013-06 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 2: CALLIPER DEPTH GAUGES; DESIGN AND METROLOGICAL CHARACTERISTICS (ISO 13385-2:2011)
    DIN EN ISO 463:2006-06 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - DESIGN AND METROLOGICAL CHARACTERISTICS OF MECHANICAL DIAL GAUGES

    Standards Referencing This Book - (Show below) - (Hide below)

    DIN EN ISO 1:2015-03 (Draft) GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STANDARD REFERENCE TEMPERATURE FOR THE SPECIFICATION OF GEOMETRICAL AND DIMENSIONAL PROPERTIES (ISO 1:2016)
    ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
    ISO/TS 17450-2:2002 Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties
    ISO 12179:2000 Geometrical Product Specifications (GPS) Surface texture: Profile method Calibration of contact (stylus) instruments
    ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
    ISO/TS 14253-2:1999 Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
    ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
    DIN EN ISO 8062-3:2008-09 Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings (ISO 8062-3:2007)
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    DIN EN ISO 1 Beiblatt 1:2004-02 Geometrical product specifications (GPS) - Standard reference temperature for geometrical product specification and verification - Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences (ISO/TR 16015:2003)
    ISO 1:2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties
    DIN EN ISO 14253-1:2013-12 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - PART 1: DECISION RULES FOR PROVING CONFORMITY OR NONCONFORMITY WITH SPECIFICATIONS (ISO 14253-1:2013)
    ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
    ISO 8062-3:2007 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
    ISO 3650:1998 Geometrical Product Specifications (GPS) Length standards Gauge blocks
    DIN EN ISO 14253-1 Beiblatt 1:2000-05 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - GUIDE TO THE ESTIMATION OF UNCERTAINTY IN GPS MEASUREMENT, IN CALIBRATION OF MEASURING EQUIPMENT AND IN PRODUCT VERIFICATION
    ISO/TR 16015:2003 Geometrical product specifications (GPS) — Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences
    DIN EN ISO 2692:2015-12 Geometrical product specifications (GPS) - Geometrical tolerancing - Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) (ISO 2692:2014)
    DIN ISO/TS 17450-2:2002-05 (Draft) GEOMETRICAL PRODUCT SPECIFICATION (GSP) - GENERAL AND CONCEPTS - PART 2: BASIC TENETS, SPECIFICATIONS, OPERATORS AND UNCERTAINTIES
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective