DIN EN ISO 15874-3:2004-03
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 3: FITTINGS
Hardcopy , PDF
07-03-2021
English
01-01-2004
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material characteristics
4.1 Plastics fitting material
4.2 Metallic fitting material
4.3 Influence on water intended for human consumption
5 General characteristics
5.1 Appearance
5.2 Opacity
6 Geometrical characteristics
6.1 General
6.2 Dimensions of sockets for socket fusion and
electrofusion fittings
6.3 Dimensions of metallic fittings
7 Mechanical characteristics of plastics fittings
7.1 General
7.2 Fitting material identical to the PP pipe compound
7.3 Fitting made from PP not identical to the PP pipe
compound
7.4 Fittings made from plastics other than PP
8 Physical and chemical characteristics of plastics
components
9 Sealing elements
10 Performance requirements
11 Marking
11.1 General requirements
11.2 Minimum required marking
Bibliography
Defines the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application.
| DevelopmentNote |
Suspended until publication of a revised English text, due to a new German edition. (06/2013)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| I.S. EN ISO 15874-3:2013 | Identical |
| NEN EN ISO 15874-3 : 2013 | Identical |
| SN EN ISO 15874-3:2013 | Identical |
| UNI EN ISO 15874-3 : 2013 | Identical |
| EN ISO 15874-3:2013 | Identical |
| NBN EN ISO 15874-3 : 2013 | Identical |
| ISO 15874-3:2013 | Identical |
| UNE-EN ISO 15874-3:2013 | Identical |
| NS EN ISO 15874-3 : 2013 | Identical |
| BS EN ISO 15874-3 : 2013 | Identical |
| NF EN ISO 15874-3 : 2013 | Identical |
| ONORM EN ISO 15874-3 : 2013 | Identical |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN ISO 15874-5:2013 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013) |
| EN ISO 9080:2012 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012) |
| EN 578 : 1993 | PLASTICS PIPING SYSTEMS - PLASTICS PIPES AND FITTINGS - DETERMINATION OF THE OPACITY |
| ISO 12092:2000 | Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure Resistance to internal pressure Test method |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
| ENV 12108:2001 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| EN ISO 15874-2:2013 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013) |
| EN 12107 : 1997 | PLASTICS PIPING SYSTEM - INJECTION MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT - DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| EN ISO 15874-1:2013 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2013) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.