DIN EN ISO 294-2:2006-05
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - SMALL TENSILE BARS
Hardcopy , PDF
English
01-01-2006
15-10-2018
Foreword
1 Scope
2 Normative references
3 Definitions
4 Apparatus
5 Procedure
6 Report on test-specimen preparation
Annex ZA (normative) Normative references to international
publications with their relevant
European publications
This standard is included in DIN Handbook KUNSTSTOFFE BAND 1. Specifies a four-cavity mould, the type C ISO mould, for the injection moulding of small tensile bars measuring > 60 mm X 10 mm X 3 mm.
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN ISO 294-2 : 1998 | Identical |
| NEN EN ISO 294-2 : 1998 AMD 1 2005 | Identical |
| NF EN ISO 294-2 : 1998 AMD 1 2005 | Identical |
| BS EN ISO 294-2:1998 | Identical |
| ISO 294-2:1996 | Identical |
| I.S. EN ISO 294-2:1998 | Identical |
| NBN EN ISO 294-2 : 1998 AMD 1 2005 | Identical |
| NS EN ISO 294-2 : 1998 AMD 1 2005 | Identical |
| UNE-EN ISO 294-2:1999 | Identical |
| DIN EN ISO 20753:2014-07 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| DIN EN ISO 183:1999-10 | PLASTICS - QUALITATIVE EVALUATION OF THE BLEEDING OF COLORANTS |
| DIN EN ISO 1622-2:1999-10 | PLASTICS - POLYSTYRENE (PS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 6721-1:2011-08 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| DIN EN ISO 4892-1:2016-10 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016) |
| DIN HDBK KUNSTSTOFFE BAND 1 : 2016 | HANDBUCH KUNSTSTOFFE - BAND 1 - MECHANISCHE UND THERMISCHE EIGENSCHAFTEN - PRUEFNORMEN |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.