DIN EN ISO 4613-2:2004-12
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS - ETHYLENE/VINYL ACETATE (E/VAC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
Hardcopy , PDF
English
01-01-2004
07-03-2021
Foreword
1 Scope
2 Normative references
3 Preparation of test specimens
4 Conditioning of test specimens
5 Determination of properties
This standard is included in DIN Handbook KUNSTSTOFFE BAND 3. Describes the methods of preparation of test specimens and the test methods to be used in determining the properties of E/VAC moulding and extrusion materials.
| DevelopmentNote |
Supersedes DIN 16778-2 (07/2002)
|
| DocumentType |
Standard
|
| Pages |
9
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| NEN EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| NS EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| NF EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| NBN EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| BS EN ISO 4613-2:1995 | Identical |
| ISO 4613-2:1995 | Identical |
| I.S. EN ISO 4613-2:1996 | Identical |
| UNE-EN ISO 4613-2:1996 | Identical |
| DIN HDBK KUNSTSTOFFE BAND 3 : 2016 | HANDBUCH KUNSTSTOFFE - BAND 3 - THERMOPLASTISCHE KUNSTSTOFF-FORMMASSEN |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 75-1:2013 | Plastics — Determination of temperature of deflection under load — Part 1: General test method |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| ISO 527-4:1997 | Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 8985:1998 | Plastics — Ethylene/vinyl acetate copolymer (EVAC) thermoplastics — Determination of vinyl acetate content |
| ISO 4613-1:1993 | Plastics — Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials — Part 1: Designation and specification |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 10350:1993 | Plastics — Acquisition and presentation of comparable single-point data |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 1628-3:2010 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 3: Polyethylenes and polypropylenes |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 1183:1987 | Plastics — Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| ISO 3146:2000 | Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| ISO 62:2008 | Plastics — Determination of water absorption |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 179:1993 | Plastics — Determination of Charpy impact strength |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.