Skip to content
Please enter a keyword to search

  • DIN ISO 1101:1985-03

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    TECHNICAL DRAWINGS, GEOMETRICAL TOLERANCING, TOLERANCES OF FORM, ORIENTATION, LOCATION AND RUNOUT - GENERALITIES, DEFINITIONS, SYMBOLS ON DRAWINGS

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-02-2006

    Language(s):  English

    Published date:  01-01-1985

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    0 Einführung
    1 Anwendungsbereich und Zweck
    2 Verweisungen auf andere Normen
    3 Allgemeines
    4 Symbole
    5 Toleranzrahmen
    6 Tolerierte Elemente
    7 Toleranzzonen
    8 Bezüge
    9 Einschränkende Festlegungen
    10 Theoretisch genaue Masse
    11 Projizierte (vorgelagerte) Toleranzzone
    12 Maximum-Material-Bedingung
    13 Definitionen der Toleranzzonen
    14 Detaillierte Definitionen der Toleranzen
       14.1 Geradheitstoleranz
       14.2 Ebenheitstoleranz
       14.3 Rundheitstoleranz
       14.4 Zylinderformtoleranz
       14.5 Profilformtoleranz einer beliebigen Linie
       14.6 Profilformtoleranz einer beliebigen Fläche
       14.7 Parallelitätstoleranz
       14.8 Rechtwinkligkeitstoleranz
       14.9 Neigungstoleranz
       14.10 Positionstoleranz
       14.11 Konzentrizitäts- und Koaxialitätstoleranz
       14.12 Symmetrie
       14.13 Lauftoleranz (Rundlauf, Planlauf)
       14.14 Gesamtlauftoleranz (Gesamtrundlauf, Gesamtplanlauf)

    Abstract - (Show below) - (Hide below)

    This standard is included in DIN Handbook 1, 148 and 303.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DIN 7184, DIN 7184-1 and DIN 7184 SUPP 1 (07/2002)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BWB TL 4240-0060 : 1ED 2002 COMBINATION FILTER, 60 CBM/HOUR, FOR NBC OVERPRESSURE SYSTEM
    BWB TL 5120-0076 : 4ED 2006 COMBINATION WRENCH I.A.W. DIN 3113
    DIN 7081:1999-05 PRESSURE RESISTANT OBLONG SIGHT GLASSES OF BOROSILICATE GLASS WITHOUT LIMITATION IN THE RANGE OF LOW TEMPERATURE
    DIN 1834-2:1990-04 Narrow side and face milling cutters; technical delivery conditions
    DIN 327-2:1990-04 PARALLEL SHANK SLOT DRILLS - TECHNICAL DELIVERY CONDITIONS
    BWB TL 5120-0074 : 5ED JUL 2006 DOUBLE-HEAD BOX WRENCH I.A.W. DIN 838
    DIN HDBK 148 : 7ED 2003 ENGINEERING DRAWINGS 2 - DIN EN 10052 TO DIN EN 61355, DIN EN ISO 3098-0 TO DIN EN ISO 11091, DIN ISO 128-20 TO DIN ISO 4066
    DIN ISO 1660:1988-07 TECHNICAL DRAWINGS - DIMENSIONING AND TOLERANCING OF PROFILES
    DIN EN 14781:2006-03 RACING BICYCLES - SAFETY REQUIREMENTS AND TEST METHODS
    DIN EN ISO 15732:2005-09 Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramics at room temperature by single edge precracked beam (SEPB) method (ISO 15732:2003)
    DIN 885-2:1990-05 Side milling cutters; technical delivery conditions
    DIN ISO 2768-2:1991-04 General tolerances; geometrical tolerances for features without individual tolerances indications; identical with ISO 2768-2:1989
    DIN ISO 128-22:1999-11 Technical drawings - General principles of presentation - Part 22: Basic conventions and applications for leader lines and reference lines (ISO 128-22:1999)
    DIN 2272-1:1985-08 INSPECTION EQUIPMENT USED IN DIMENSIONAL METROLOGY - REQUIREMENTS AUXILIARY MEASURING DEVICES
    DKD-R 4-3-4.2 : 2010 KALIBRIEREN VON MESSMITTELN FUER GEOMETRISCHE MESSGROESSEN - BLATT 4.2: KALIBRIEREN VON PRUEFSTIFTEN/GEWINDEPRUEFSTIFTEN
    DIN 34110:1991-11 PISTON RINGS FOR GENERAL ENGINEERING - R-RINGS, PLAIN COMPRESSION RINGS, 10 UP TO 1200 MM NOMINAL DIAMETER
    DKD-R 4-3-4.1 : 2002 KALIBRIEREN VON MESSMITTELN FUER GEOMETRISCHE MESSGROESSEN - BLATT 4.1: KALIBRIEREN VON ZYLINDRISCHEN EINSTELLNORMALEN, LEHRDORNEN UND -RINGEN
    DIN 820-24:1986-11 STANDARDIZATION; PRESENTATION OF STANDARDS; FIGURES AND TABLES
    DIN 59700:1986-08 WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS; EXTRUDED SQUARE BARS; TOLERANCES ON DIMENSIONS AND FORMS
    DIN 7867:1986-06 V-RIBBED BELTS AND CORRESPONDING PULLEYS
    DIN V 76622:1990-06 INTERNAL COMBUSTION ENGINES - PISTON RINGS - RECTANGULAR RINGS WITH NARROW RING WIDTH
    DIN 8601:1986-12 MACHINE TOOLS; ACCEPTANCE CONDITIONS FOR MACHINE TOOLS OPERATING BY REMOVING METAL; GENERAL RULES
    DIN IEC 60297-3:1994-08 DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3: SUBRACKS AND ASSOCIATED PLUG-IN UNITS
    DIN 16966-7:1995-04 PIPE JOINTS AND THEIR ELEMENTS OF GLASS FIBRE REINFORCED POLYESTER RESINS - PART 7: BUSHINGS, FLANGES, FLANGED AND BUTT JOINTS - GENERAL QUALITY REQUIREMENTS AND TEST METHODS
    DIN EN ISO 10360-6:2009-01 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 6: ESTIMATION OF ERRORS IN COMPUTING GAUSSIAN ASSOCIATED FEATURES
    VDI/VDE 2631 Blatt 7:2012-02 Form measurement - Determination of positional deviations of the form-measurement axes
    VDI/VDE 2617 Blatt 2.2:2000-07 Accuracy of coordinate measuring machines - Parameters and their reverification - Form measurement
    DIN 503:2004-09 Driving components - Flange bearings - Fastened with four screws
    DIN 7080:2005-05 Pressure resistant circular sight glasses of borosilicate glass without limitation in the range of low temperature
    DIN 51224:1985-01 MATERIALS TESTING MACHINES; HARDNESS TESTING MACHINES WITH A DEPTH-MEASURING DEVICE
    DIN 72311-20:1989-05 LEAD STORAGE BATTERIES; STARTER BATTERIES FOR COMMERCIAL VEHICLES; NOMINAL CAPACITIES AND MAIN DIMENSIONS
    DIN 2269:1998-11 VERIFICATION OF GEOMETRICAL PARAMETERS - CYLINDRICAL MEASURING PIN
    DIN 847-2:1990-05 DOUBLE EQUAL-ANGLE CUTTERS - TECHNICAL DELIVERY CONDITIONS
    DIN EN 50066 : 1994 APPLIANCE COUPLERS FOR HOUSEHOLD AND SIMILAR GENERAL PURPOSES; MINI-COUPLERS FOR THE INTERCONNECTION OF ELECTRICAL MAINS SUPPLIED EQUIPMENT IN ROAD VEHICLES
    BWB TL 5120-0120 : 1ED 2005
    DIN 28060:1986-11 BRICK-LINED VESSELS AND APPARATUS - DESIGN AND CONSTRUCTION
    BWB TL 4320-0025 : 2ED 1997 FUEL PUMPING SYSTEM, 400 L/MIN
    DIN 1770:1987-01 WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS, EXTRUDED RECTANGULAR BARS - TOLERANCES ON DIMENSIONS AND FORMS, STATIC VALUES
    DIN 58413:1987-11 TOLERANCES FOR GEAR HOBS FOR FINE MECHANICS
    DIN 7643:2005-07 COMPRESSION COUPLINGS - HOLLOW SCREWS FOR RING-TYPE BANJOS
    DIN 7168:1991-04 GENERAL TOLERANCES FOR LINEAR AND ANGULAR DIMENSIONS AND GENERAL GEOMETRICAL TOLERANCES
    DIN 1769:1986-09 WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS - DRAWN RECTANGULAR BARS WITH SHARP EDGES - TOLERANCES ON DIMENSIONS AND FORMS, STATIC VALUES
    DIN EN ISO 13920:1996-11 General tolerances for welded constructions - Tolerances for lengths, angles, shape and position (ISO 13920:1996)
    DIN 70907:1991-04 PISTON RINGS - TEST OF QUALITY CHARACTERISTICS - TERMS, MEASURING PROCEDURES - SUPPLEMENT TO DIN ISO 6621 PART 2
    DIN 28060 Beiblatt 1:1986-12 BRICK-LINED VESSELS AND APPARATUS - EXAMPLES FOR TEST METHODS FOR TOLERANCES
    BWB TL 5120-0078 : 3ED 2006 DOUBLE-HEAD BOX WRENCHES I.A.W. DIN 837
    DIN 8620-2:1994-01 MACHINE TOOLS - BORING AND MILLING MACHINES WITH HORIZONTAL SPINDLE - TABLE TYPE MACHINES, ACCEPTANCE CONDITIONS
    DKD-R 4-3-4.12 : 2010 KALIBRIEREN VON MESSMITTELN FUER GEOMETRISCHE MESSGROESSEN - BLATT 4.12: KALIBRIEREN VON KEGELNORMALEN UND KEGELLEHREN
    DIN 810:1986-11 MACHINE TOOLS; PRESSES; SLIDE HOLES FOR SHANKS OF PRESS TOOLS; DIMENSIONS
    DIN 842-2:1990-01 SHELL TYPE SINGLE-ANGLE MILLING CUTTERS; TECHNICAL DELIVERY CONDITIONS
    VDE 0625-10 : 1994 APPLIANCE COUPLERS FOR HOUSEHOLD AND SIMILAR GENERAL PURPOSES; MINI-COUPLERS FOR THE INTERCONNECTION OF ELECTRICAL MAINS SUPPLIED EQUIPMENT IN ROAD VEHICLES
    DIN 72311-21:1988-01 LEAD STORAGE BATTERIES; STARTER BATTERIES WITH 10,5 BASIC FASTENING LUGS FOR COMMERCIAL VEHICLES; NOMINAL CAPACITIES AND MAIN DIMENSIONS
    DIN ISO 7083:1984-06 Technical drawings; symbols for geometrical tolerancing; proportions and dimensions
    DIN ISO 3302-2:1999-10 RUBBER - TOLERANCES FOR PRODUCTS - PART 2: GEOMETRICAL TOLERANCES
    DIN VDE 0625-1 : 1987 APPLIANCE COUPLERS FOR HOUSEHOLD AND SIMILAR GENERAL PURPOSES
    DIN ISO 9939:1995-12 AEROSPACE - PRESSURE RE-OILING CONNECTION (NEW TYPE)
    DIN EN ISO 3650:1999-02 Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998); German version EN ISO 3650:1998
    DIN EN 14764:2006-03 CITY AND TREKKING BICYCLES - SAFETY REQUIREMENTS AND TEST METHODS
    DIN 17615-3:1987-01 ALMGSI0,5 PRECISION SECTIONS - TOLERANCES
    DKD-R 4-4 : 2009 KALIBRIEREN VON NORMALEN UND MESSGERAETEN FUER DIE FORMMESSTECHNIK
    DIN 59701:1986-08 WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS; EXTRUDED HEXAGONAL BARS; TOLERANCES ON DIMENSIONS AND FORMS
    DIN 1833-2:1990-04 PARALLEL SHANK DOVETAIL CUTTERS - TECHNICAL DELIVERY CONDITIONS
    DIN 502:2004-09 Driving Components - Flange bearings - Fastened with two screws
    DIN 850-2:1990-04 WOODRUFF CUTTERS; TECHNICAL DELIVERY CONDITIONS
    DIN 7168-2:1986-07 GENERAL TOLERANCES - GEOMETRICAL TOLERANCES
    DIN EN ISO 4759-1 E : 2001 TOLERANCES FOR FASTENERS - PART 1: BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C
    DIN ISO 230-1:1999-07 TEST CODE FOR MACHINE TOOLS - PART 1: GEOMETRIC ACCURACY OF MACHINES OPERATING UNDER NO-LOAD OR FINISHING CONDITIONS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
    ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
    ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
    ISO 7083:1983 TECHNICAL DRAWINGS - SYMBOLS FOR GEOMETRICAL TOLERANCING - PROPORTIONS AND DIMENSIONS
    ISO 129:1985 Technical drawings Dimensioning General principles, definitions, methods of execution and special indications
    ISO 1660:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing
    ISO 128:1982 Technical drawings — General principles of presentation
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective