Skip to content
Please enter a keyword to search

  • EN 12668-2:2010

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 2: Probes

    Available format(s): 

    Superseded date:  19-02-2022

    Language(s): 

    Published date:  03-02-2010

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General requirements for compliance
    5 Technical specification for probes
    6 Test equipment
    7 Performance requirements for probes
    Annex A (normative) - Calculation of near field length
            of non-focusing probes
    Annex B (informative) - Calibration block for angle-beam
            probes
    Bibliography

    Abstract - (Show below) - (Hide below)

    This European Standard covers probes used for ultrasonic non-destructive examination in the following categories with centre frequencies in the range 0,5 MHz to 15 MHz, focusing and without focusing means:a)single or dual transducer contact probes generating compressional or shear waves;b)single transducer immersion probes.Where material-dependent ultrasonic values are specified in this document they are based on steels having a sound velocity of (5 920 ± 50) m/s for longitudinal waves, and (3 255 ± 30) m/s for transverse waves.Periodic tests for probes are not included in this document. Routine tests for the verification of probes using on-site methods are given in EN 12668-3.If parameters in addition to those specified in EN 12668-3 are to be verified during the probe's life time, as agreed upon by the contracting parties, the methods of verification for these additional parameters should be selected from those given in this document.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 138
    Development Note Supersedes PREN 12668-2. (10/2005)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    UNE-EN 15317:2014 Non-destructive testing - Ultrasonic testing - Characterization and verification of ultrasonic thickness measuring equipment
    10/30198090 DC : 0 BS EN ISO 13588 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - USE OF (SEMI-) AUTOMATED PHASED ARRAY TECHNOLOGY
    UNI EN ISO 17405 : 2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TECHNIQUE OF TESTING CLADDINGS PRODUCED BY WELDING, ROLLING AND EXPLOSION
    DIN EN ISO 16828:2014-06 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES (ISO 16828:2012)
    DIN EN 583-6:2009-03 NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - PART 6: TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES
    DIN EN 12668-3 E : 2014 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT
    DIN EN ISO 16810 E : 2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - GENERAL PRINCIPLES (ISO 16810:2012)
    I.S. EN ISO 16828:2014 ON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES (ISO 16828:2012)
    DIN EN ISO 17405 E : 2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TECHNIQUE OF TESTING CLADDINGS PRODUCED BY WELDING, ROLLING AND EXPLOSION (ISO 17405:2014)
    DIN EN ISO 18563-3:2016-06 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS (ISO 18563-3:2015)
    12/30270659 DC : 0 BS EN 10228-3 - NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS
    17/30326176 DC : 0 BS EN 16729-3 - RAILWAY APPLICATIONS - INFRASTRUCTURE - NON-DESTRUCTIVE TESTING ON RAILS IN TRACK - PART 3: REQUIREMENTS FOR IDENTIFYING INTERNAL AND SURFACE RAIL DEFECTS
    04/30123014 DC : DRAFT SEP 2004 ISO 4992-2 - STEEL CASTINGS - ULTRASONIC EXAMINATION - PART 2: STEEL CASTINGS FOR HIGHLY STRESSED COMPONENTS
    DD CEN/TS 14751:2004 Welding. Use of time-of-flight diffraction technique (TOFD) for examination of welds
    UNE-EN ISO 17405:2015 Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014)
    07/30135963 DC : 0 BS EN 1714 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS
    ISO 16831:2012 Non-destructive testing — Ultrasonic testing — Characterization and verification of ultrasonic thickness measuring equipment
    I.S. EN ISO 16810:2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - GENERAL PRINCIPLES (ISO 16810:2012)
    BS EN 16910-1:2018 Railway applications. Rolling stock. Requirements for non-destructive testing on running gear in railway maintenance Wheelsets
    EN ISO 22825:2017 NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS (ISO 22825:2017)
    EN 10228-3:2016 Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings
    BS EN 10306:2002 Iron and steel. Ultrasonic testing of H beams with parallel flanges and IPE beams
    UNE-EN 12680-3:2012 Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings
    BS EN 10307:2001 Non-destructive testing. Ultrasonic testing of austenitic and austentitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method)
    DIN EN 13100-3:2005-02 Non-destructive testing of welded joints in thermoplastics semi-finished products - Part 3: Ultrasonic testing
    EN 12680-1:2003 Founding - Ultrasonic examination - Part 1: Steel castings for general purposes
    EN 10308:2001 Non destructive testing - Ultrasonic testing of steel bars
    EN 10306:2001 Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams
    EN 10307:2001 Non-destructive testing - Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method)
    DIN EN 12680-2:2003-06 Founding - Ultrasonic examination - Part 2: Steel castings for highly stressed components; German version EN 12680-2:2003
    EN 12680-3:2011 Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings
    DIN EN 10307:2002-03 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEELS FLAT PRODUCTS OF THICKNESS EQUAL TO OR GREATER THAN 6 MM (REFLECTION METHOD)
    EN 12680-2:2003 Founding - Ultrasonic examination - Part 2: Steel castings for highly stressed components
    DIN EN 12680-3:2012-02 Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings
    CEN/TS 14751:2004 Welding - Use of time-of-flight diffraction technique (TOFD) for examination of welds
    EN 12668-3:2013 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment
    EN 10228-4:2016 Non-destructive testing of steel forgings - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings
    EN 13100-3:2004 Non destructive testing of welded joints in thermoplastics semi-finished products - Part 3: Ultrasonic testing
    UNI EN 16090 : 2012 COPPER AND COPPER ALLOYS - ESTIMATION OF AVERAGE GRAIN SIZE BY ULTRASOUND
    I.S. CEN TS 14751:2004 WELDING - USE OF TIME-OF-FLIGHT DIFFRACTION TECHNIQUE (TOFD) FOR EXAMINATION OF WELDS
    BS ISO 18610:2016 Fine ceramics (advanced ceramics, advanced technical ceramics). Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure. Determination of elastic properties by ultrasonic technique
    BS EN ISO 18563-3:2015 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS
    10/30218967 DC : 0 BS EN 12680-3 - FOUNDING - ULTRASONIC EXAMINATION - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS
    12/30270662 DC : 0 BS EN 10228-4 - NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS
    BS ISO 4992-2:2006 Steel castings. Ultrasonic examination Steel castings for highly stressed components
    UNI EN 583-6 : 2009 NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - PART 6: TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES
    PREN 10228-4 : DRAFT 2012 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS
    I.S. EN 16090:2011 COPPER AND COPPER ALLOYS - ESTIMATION OF AVERAGE GRAIN SIZE BY ULTRASOUND
    DIN EN 12680-3 E : 2012 FOUNDING - ULTRASONIC TESTING - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS
    DIN EN 12680-2 E : 2003 FOUNDING - ULTRASONIC EXAMINATION - PART 2: STEEL CASTINGS FOR HIGHLY STRESSED COMPONENTS
    DIN EN 12680-1 E : 2003 FOUNDING - ULTRASONIC EXAMINATION - PART 1: STEEL CASTINGS FOR GENERAL PURPOSES
    DIN EN 15317 E : 2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT
    DIN EN 15317:2014-02 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT
    BS EN 10308:2002 Non-destructive testing. Ultrasonic testing of steel bars
    I.S. EN 10228-3:2016 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS
    UNI EN 12668-3 : 2013 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT
    I.S. EN 12668-3:2013 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT
    I.S. EN 15317:2013 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT
    I.S. EN 10228-4:2016 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS
    I.S. EN 12680-3:2011 FOUNDING - ULTRASONIC TESTING - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS
    13/30277410 DC : 0 BS EN 15317 - NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT
    DIN EN 12668-3:2014-02 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment
    BS EN 16090:2011 Copper and copper alloys. Estimation of average grain size by ultrasound
    UNI EN ISO 16828 : 2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES
    DIN EN ISO 17405:2014-10 Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014); German version EN ISO 17405:2014
    PREN 12799 : DRAFT 2017 BRAZING - NON-DESTRUCTIVE EXAMINATION OF BRAZED JOINTS
    10/30195043 DC : 0 BS EN ISO 22825 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS
    18/30337971 DC : DRAFT APR 2018 BS ISO 20890-1 - IN-SERVICE INSPECTIONS FOR PRIMARY COOLANT CIRCUIT COMPONENTS OF LIGHT WATER REACTORS - PART 1: MECHANIZED ULTRASONIC TESTING
    DIN EN ISO 16828 E : 2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES (ISO 16828:2012)
    BS ISO 4992-1:2006 Steel castings. Ultrasonic examination Steel castings for general purposes
    DIN EN 16090:2012-02 COPPER AND COPPER ALLOYS - ESTIMATION OF AVERAGE GRAIN SIZE BY ULTRASOUND
    04/30123011 DC : DRAFT SEP 2004 ISO 4992-1 - STEEL CASTINGS - ULTRASONIC EXAMINATION - PART 1: STEEL CASTINGS FOR GENERAL PURPOSES
    DIN EN ISO 16810:2014-07 Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
    16/30345944 DC : 0 BS EN ISO 22825 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS
    I.S. EN 583-6:2008 NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - PART 6: TIMEOF- FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES
    UNE-EN ISO 16828:2014 Non-destructive testing - Ultrasonic testing - Time-of-flight diffraction technique as a method for detection and sizing of discontinuities (ISO 16828:2012)
    ISO 22825:2017 Non-destructive testing of welds — Ultrasonic testing — Testing of welds in austenitic steels and nickel-based alloys
    UNE-EN 10228-4:2016 Non-destructive testing of steel forgings - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings
    UNE-EN 10228-3:2016 Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings
    BS EN 12680-3:2011 Founding. Ultrasonic testing Spheroidal graphite cast iron castings
    UNE-EN 16090:2012 Copper and copper alloys - Estimation of average grain size by ultrasound
    UNI EN 15317 : 2013 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT
    UNI EN 12680-3 : 2012 FOUNDING - ULTRASONIC TESTING - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS
    15/30270299 DC : 0 BS EN 16910 - RAILWAY APPLICATIONS - ROLLING STOCK - REQUIREMENTS FOR NONDESTRUCTIVE TESTING ON RUNNING GEAR IN RAILWAY MAINTENANCE
    15/30280621 DC : 0 BS ISO 18610 - FINE CERAMICS (ADVANCED CERAMICS, ADVANCED TECHNICAL CERAMICS) - MECHANICAL PROPERTIES OF CERAMIC COMPOSITES AT ROOM TEMPERATURE - DETERMINATION OF ELASTIC PROPERTIES BY AN ULTRASONIC TECHNIQUE
    PREN 12668-3 : DRAFT 2013 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT
    BS EN 583-6:2008 Non-destructive testing. Ultrasonic examination Time-of-flight diffraction technique as a method for detection and sizing of discontinuities
    BS EN ISO 16828:2014 Non-destructive testing. Ultrasonic testing. Time-of-flight diffraction technique as a method for detection and sizing of discontinuities
    I.S. EN 16910-1:2018 RAILWAY APPLICATIONS - ROLLING STOCK - REQUIREMENTS FOR NON-DESTRUCTIVE TESTING ON RUNNING GEAR IN RAILWAY MAINTENANCE - PART 1: WHEELSETS
    DD ENV 583-6:2000 Non-destructive testing. Ultrasonic examination Time-of-flight diffraction technique as a method for detection and sizing of discontinuities
    03/115417 DC : DRAFT SEP 2003 BS EN ISO 22825 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC METHOD - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL BASED ALLOYS
    PREN 10228-3 : DRAFT 2012 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS
    ISO 12715:2014 Non-destructive testing Ultrasonic testing Reference blocks and test procedures for the characterization of contact probe sound beams
    EN 16910-1:2018 Railway applications - Rolling stock - Requirements for non-destructive testing on running gear in railway maintenance - Part 1: Wheelsets
    BS EN ISO 22825:2017 Non-destructive testing of welds. Ultrasonic testing. Testing of welds in austenitic steels and nickel-based alloys
    KTA 3211.1 : 2015 PRESSURE AND ACTIVITY RETAINING COMPONENTS OF SYSTEMS OUTSIDE THE PRIMARY CIRCUIT - PART 1: MATERIALS
    ISO 4992-1:2006 Steel castings Ultrasonic examination Part 1: Steel castings for general purposes
    I.S. EN ISO 22825:2017 NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS (ISO 22825:2017)
    UNE-EN 12668-3:2014 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment
    DIN EN 10228-4:2016-10 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS
    DIN EN 10228-3:2016-10 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS
    ISO 16810:2012 Non-destructive testing — Ultrasonic testing — General principles
    BS EN 12680-1:2003 Founding. Ultrasonic examination Steel castings for general purposes
    BS EN 12680-2:2003 Founding. Ultrasonic examination Steel castings for highly stressed components
    BS EN 15317:2013 Non-destructive testing. Ultrasonic testing. Characterization and verification of ultrasonic thickness measuring equipment
    BS EN 10228-4:2016 Non-destructive testing of steel forgings Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings
    BS EN 13100-3:2004 Non-destructive testing of welded joints in thermoplastics semi-finished products Ultrasonic testing
    UNE-EN ISO 16810:2014 Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
    UNE-EN ISO 18563-3:2016 Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 3: Combined systems (ISO 18563-3:2015)
    BS EN 10228-3:2016 Non-destructive testing of steel forgings Ultrasonic testing of ferritic or martensitic steel forgings
    ISO 18563-3:2015 Non-destructive testing Characterization and verification of ultrasonic phased array equipment Part 3: Combined systems
    ISO 16828:2012 Non-destructive testing — Ultrasonic testing — Time-of-flight diffraction technique as a method for detection and sizing of discontinuities
    EN ISO 16810:2014 Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
    EN ISO 18563-3:2015 Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 3: Combined systems (ISO 18563-3:2015)
    EN 15317:2013 Non-destructive testing - Ultrasonic testing - Characterization and verification of ultrasonic thickness measuring equipment
    EN 16090:2011 Copper and copper alloys - Estimation of average grain size by ultrasound
    EN ISO 17405:2014 Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014)
    EN 16729-3:2018 Railway applications - Infrastructure - Non-destructive testing on rails in track - Part 3: Requirements for identifying internal and surface rail defects
    EN ISO 16828:2014 Non-destructive testing - Ultrasonic testing - Time-of-flight diffraction technique as a method for detection and sizing of discontinuities (ISO 16828:2012)
    EN 583-6:2008 Non-destructive testing - Ultrasonic examination - Part 6: Time-of-flight diffraction technique as a method for detection and sizing of discontinuities
    UNE-EN 583-6:2010 Non-destructive testing - Ultrasonic examination - Part 6: Time-of-flight diffraction technique as a method for detection and sizing of discontinuities
    DIN EN ISO 18563-3 E : 2016 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS (ISO 18563-3:2015)
    I.S. EN ISO 17405:2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TECHNIQUE OF TESTING CLADDINGS PRODUCED BY WELDING, ROLLING AND EXPLOSION (ISO 17405:2014)
    09/30187580 DC : DRAFT SEP 2009 BS EN ISO 10863 - WELDING - USE OF TIME-OF-FLIGHT DIFFRACTION TECHNIQUE (TOFD) FOR TESTING OF WELDS
    13/30277407 DC : 0 BS EN 12668-3 - NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT
    BS EN ISO 17405:2014 Non-destructive testing. Ultrasonic testing. Technique of testing claddings produced by welding, rolling and explosion
    BS EN ISO 16810:2014 Non-destructive testing. Ultrasonic testing. General principles
    PREN 12680-3 : DRAFT 2010 FOUNDING - ULTRASONIC EXAMINATION - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS
    I.S. EN ISO 18563-3:2015 NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS (ISO 18563-3:2015)
    ISO 18610:2016 Fine ceramics (advanced ceramics, advanced technical ceramics) Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure Determination of elastic properties by ultrasonic technique
    ISO 4992-2:2006 Steel castings Ultrasonic examination Part 2: Steel castings for highly stressed components
    I.S. EN 16729-3:2018 RAILWAY APPLICATIONS - INFRASTRUCTURE - NON-DESTRUCTIVE TESTING ON RAILS IN TRACK - PART 3: REQUIREMENTS FOR IDENTIFYING INTERNAL AND SURFACE RAIL DEFECTS
    17/30359544 DC : 0 BS EN 12799 - BRAZING - NON-DESTRUCTIVE EXAMINATION OF BRAZED JOINTS
    UNI EN ISO 16810 : 2014 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - GENERAL PRINCIPLES
    KTA 3201.3 : 2007(R2012) COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS - PART 3: MANUFACTURE
    BS EN 12668-3:2013 Non-destructive testing. Characterization and verification of ultrasonic examination equipment Combined equipment
    ISO 17405:2014 Non-destructive testing Ultrasonic testing Technique of testing claddings produced by welding, rolling and explosion
    DIN EN 10228-3:1998-07 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS
    DIN EN 10228-4:1999-10 NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS
    DIN EN 10306:2002-04 IRON AND STEEL - ULTRASONIC TESTING OF H BEAMS WITH PARALLEL FLANGES AND IPE BEAMS
    DIN EN 12680-1:2003-06 Founding - Ultrasonic examination - Part 1: Steel castings for general purposes; German version EN 12680-1:2003
    DIN EN 10308:2002-03 NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING OF STEEL BARS

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 7963:2010 Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2006)
    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    EN 1330-4:2010 Non-destructive testing - Terminology - Part 4: Terms used in ultrasonic testing
    EN 12668-1:2010 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 9001:2015 Quality management systems — Requirements
    EN 12668-3:2013 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment
    ISO 7963:2006 Non-destructive testing — Ultrasonic testing —- Specification for calibration block No. 2
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective