Skip to content
Please enter a keyword to search

  • EN 13231-3:2012

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Railway applications - Track - Acceptance of works - Part 3: Acceptance of reprofiling rails in track

    Available format(s): 

    Superseded date:  19-02-2022

    Language(s): 

    Published date:  25-01-2012

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Longitudinal profile
    5 Transverse profile
    6 Metal removal
    7 Surface roughness
    8 Visual appearance: acceptance criteria
    Annex A (normative) - Procedures to verify reference
            instruments
    Annex B (normative) - Procedures to demonstrate
            correlation of approved and reference instruments
    Annex C (normative) - Calculation of peak to peak values
    Annex D (normative) - Method of periodic verification
    Annex E (informative) - Example of acceptance documentation
            for rail reprofiling work
    Bibliography

    Abstract - (Show below) - (Hide below)

    This European Standard specifies the technical requirements and the measurements to be made for the acceptance of work to reprofile longitudinally and/or transversely the heads of railway rails. For acceptance purposes, two classes of longitudinal profile and three classes of transverse profile tolerance are defined.Annexes describe procedures to verify reference instruments to be used for these measurements as well as methods to approve non-reference instruments to be used for measurements.This European Standard applies to reprofiled vignole railway rails 46 kg/m and above.It does not apply for acoustic rail reprofiling.A form of acceptance documentation that may be used is given in Annex E.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 256
    Development Note Supersedes PREN 13231-3. (02/2012)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 13848-5:2017 Railway applications. Track. Track geometry quality Geometric quality levels. Plain line, switches and crossings
    PREN 15610 : DRAFT 2017 RAILWAY APPLICATIONS - ACOUSTICS - RAIL AND WHEEL ROUGHNESS MEASUREMENT RELATED TO ROLLING NOISE GENERATION
    EN 13231-4:2013 Railway applications - Track - Acceptance of works - Part 4: Acceptance of reprofiling rails in switches and crossings
    I.S. EN 13231-4:2013 RAILWAY APPLICATIONS - TRACK - ACCEPTANCE OF WORKS - PART 4: ACCEPTANCE OF REPROFILING RAILS IN SWITCHES AND CROSSINGS
    BS EN 13231-4:2013 Railway applications. Track. Acceptance of works Acceptance of reprofiling rails in switches and crossings
    16/30258487 DC : 0 BS EN 13231-5 - RAILWAY APPLICATIONS - TRACK - ACCEPTANCE OF WORKS - PART 5: PROCEDURES FOR RAIL REPROFILING IN PLAIN LINE, SWITCHES, CROSSINGS AND EXPANSION DEVICES
    I.S. EN 15610:2009 RAILWAY APPLICATIONS - NOISE EMISSION - RAIL ROUGHNESS MEASUREMENT RELATED TO ROLLING NOISE GENERATION
    PREN 13231-5 : DRAFT 2016 RAILWAY APPLICATIONS - TRACK - ACCEPTANCE OF WORKS - PART 5: PROCEDURES FOR RAIL REPROFILING IN PLAIN LINE, SWITCHES, CROSSINGS AND EXPANSION DEVICES
    UNE-EN 13231-4:2014 Railway applications - Track - Acceptance of works - Part 4: Acceptance of reprofiling rails in switches and crossings
    UNI EN 15610 : 2009 RAILWAY APPLICATIONS - NOISE EMISSION - RAIL ROUGHNESS MEASUREMENT RELATED TO ROLLING NOISE GENERATION
    DIN EN 15610:2009-08 Railway applications - Noise emission - Rail roughness measurement related to rolling noise generation
    BS EN 15610:2009 Railway applications. Noise emission. Rail roughness measurement related to rolling noise generation
    DIN EN 15610 E : 2009 RAILWAY APPLICATIONS - NOISE EMISSION - RAIL ROUGHNESS MEASUREMENT RELATED TO ROLLING NOISE GENERATION
    EN 15610:2009 Railway applications - Noise emission - Rail roughness measurement related to noise generation
    DIN EN 13231-4:2013-06 Railway applications - Track - Acceptance of works - Part 4: Acceptance of reprofiling rails in switches and crossings
    UNI EN 13231-4 : 2013 RAILWAY APPLICATIONS - TRACK - ACCEPTANCE OF WORKS - PART 4: ACCEPTANCE OF REPROFILING RAILS IN SWITCHES AND CROSSINGS
    17/30304301 DC : 0 BS EN 15610 - RAILWAY APPLICATIONS - ACOUSTICS - RAIL AND WHEEL ROUGHNESS MEASUREMENT RELATED TO ROLLING NOISE GENERATION
    UNE-EN 15610:2010 Railway applications - Noise emission - Rail roughness measurement related to rolling noise generation

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 4287:1998/A1:2009 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - TERMS, DEFINITIONS AND SURFACE TEXTURE PARAMETERS
    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    EN ISO 4288 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - RULES AND PROCEDURES FOR THE ASSESSMENT OF SURFACE TEXTURE
    EN ISO 11562:1997/AC:2008 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - METROLOGICAL CHARACTERISTICS OF PHASE CORRECT FILTERS
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 3274:1996 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
    EN ISO 3611:2010 Geometrical product specifications (GPS) - Dimensional measuring equipment: Micrometers for external measurements - Design and metrological characteristics (ISO 3611:2010)
    ISO 3611:2010 Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
    EN ISO 10360-2:2009 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009)
    EN ISO 3274 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - NOMINAL CHARACTERISTICS OF CONTACT (STYLUS) INSTRUMENTS
    ISO 10360-2:2009 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 2: CMMs used for measuring linear dimensions
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective