EN 13244-1:2002
|
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
ISO/TR 10358:1993
|
Plastics pipes and fittings Combined chemical-resistance classification table |
EN 681-1:1996/A3:2005
|
ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER |
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
EN 728:1997
|
Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
BS EN 681-1:1996
|
Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Vulcanized rubber |
ISO 4433-1:1997
|
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method |
EN 681-2:2000/A2:2005
|
ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS |
EN 60947-1:2007/A2:2014
|
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014) |
IEC 60364-1:2005
|
Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
ISO 11922-1:1997
|
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
BS 7874:1998
|
Method of test for microbiological deterioration of elastomeric seals for joints in pipework and pipelines |
EN 921:1994/AC:1995
|
PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
ISO 4433-2:1997
|
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes |
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
ISO 13955:1997
|
Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
PREN ISO 3126 : DRAFT 1999
|
PLASTICS PIPING SYSTEMS - PLASTICS PIPING COMPONENTS - MEASUREMENT AND DETERMINATION OF DIMENSIONS |
EN 60335-1:2012/A13:2017
|
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
ISO 9624:1997
|
Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges |
EN 60529:1991/AC:2016-12
|
DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
EN ISO 1133:2005
|
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS |
BS EN ISO 13479:2009
|
Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes |
ISO 4059:1978
|
Polyethylene (PE) pipes — Pressure drop in mechanical pipe-jointing systems — Method of test and requirements |
EN 13244-5:2002
|
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
EN 13244-2:2002
|
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |