• Shopping Cart
    There are no items in your cart

EN 14385:2004

Current

Current

The latest, up-to-date edition.

Stationary source emissions - Determination of the total emission of As, Cd, Cr, Co, Cu, Mn, Ni, Pb, Sb, TI and V

Published date

25-02-2004

Sorry this product is not available in your region.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Principle
5 Apparatus, chemicals and gases
6 Sampling equipment
7 Cleaning of the sampling equipment prior to sampling
8 Procedure
9 Expression of results
10 Test report
Annex A (informative) Examples of absorption vessels
Annex B (informative) Types of isokinetic equipment
Annex C (informative) Pre-cleaning procedures of the sampling
        equipment at the laboratory and determination of the
        absorption efficiency
Annex D (informative) Measurement results of two field tests
Annex E (informative) Pre-tests for the determination of the
        efficiency, of the digestion and of the performance
        of the analytical procedures
Annex ZA (informative) Relationship with EU Directives
Bibliography

This European Standard specifies a manual reference method for the determination of the mass concentration of specific elements in exhaust gases from hazardous waste incinerators. The method is applicable to each of the specific elements in the concentration range of 0,005 mg/m3 to 0,5 mg/m3. Unless otherwise stated, gas volumes are expressed at dry conditions, normalised to 273 K and oxygen content 101,3 kPa, and normalized to a dry oxygen content of 11 % on the volume/volume basis.Specific elements according to this European standard are antimony (Sb), arsenic (As), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), lead (Pb), manganese (Mn), nickel (Ni), thallium (Tl), and vanadium (V).This European standard is validated for the determination of the mass concentration of specific ele-ments in incineration exhaust gases with the composition given in Table 1.This European standard is also applicable for exhaust gases from other sources with a similar flue gas composition.

Committee
CEN/TC 264
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

Standards Relationship
BS EN 14385:2004 Identical
DIN EN 14385:2004-05 Identical
NBN EN 14385 : 2004 Identical
NEN EN 14385 : 2004 Identical
NS EN 14385 : 1ED 2004 Identical
UNI EN 14385 : 2004 Identical
UNE-EN 14385:2004 Identical
SN EN 14385 : 2004 Identical
NF EN 14385 : 2004 Identical
PN EN 14385 : 2005 Identical
I.S. EN 14385:2004 Identical

PREN 14181 : DRAFT 2012 STATIONARY SOURCE EMISSIONS - QUALITY ASSURANCE OF AUTOMATED MEASURING SYSTEMS
VDI 3950:2006-12 Stationary source emissions - Quality assurance of automated measuring and electronic data evaluation systems
VDI 3460 Blatt 1:2014-02 Emission control - Thermal waste treatment - Fundamentals
VDI 2293:2011-09 Emission control - Coal preparation plants including driers
VDI 2102 Blatt 1:2007-04 (Draft) Emission control - Secondary copper smelting and refining plants
VDI 2267 Blatt 3:2015-03 Determination of suspended matter in ambient air - Digestion variants for dust samples for the subsequent determination of the mass concentration of Al, Sb, As, Pb, Cd, Ca, Cr, Co, Fe, K, Cu, Mg, Mn, Na, Ni, Se, V and Zn
VDI 4220:2011-04 Quality assurance - Requirements on bodies for the determination of air pollutants at stationary sources and in ambient air
VDI 3898:2013-01 Emission control - Plants for dry mechanical, physio-chemical, thermal and biological soil treatment
S.R. CWA 16060:2009 ENVIRONMENTAL TECHNOLOGY VERIFICATION - AIR EMISSION ABATEMENT TECHNOLOGIES
12/30259213 DC : 0 BS EN 14181 - STATIONARY SOURCE EMISSIONS - QUALITY ASSURANCE OF AUTOMATED MEASURING SYSTEMS
UNE-CWA 16060:2010 IN Environmental technology verification - Air emission abatement technologies

EN 13284-1:2017 Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method
ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.