EN 1636-5 : 1997
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - PART 5: FITNESS FOR PURPOSE OF THE JOINTS
01-04-2006
12-01-2013
Foreword
Introduction
1. Scope
2. Normative references
3. Definitions
4. Interchangeability
5. Joints
5.1 Dimensions
5.2 Flexible and reduced-articulation joints with
elastomeric sealing components
Describes the characteristics of the fitness for purpose of glass-reinforced thermosetting plastics based on unsaturated polyester resin (GRP-UP) piping systems intended to be used for non-pressure drainage and sewerage. Also specifies the relevant test parameters for the test methods referred to in this standard which are applicable to the joints to be used in GRP-UP piping systems to be used for the conveyance of surface water or sewage below ground, outside buildings, at temperature up to 50 degree C.
| Committee |
TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| SN EN 1636-5 : 1998 | Identical |
| I.S. EN 1636-5:1998 | Identical |
| BS EN 1636-5:2001 | Identical |
| UNE-EN 1636-5:1998 | Identical |
| DIN EN 1636-5:1999-12 | Identical |
| NF EN 1636-5 : 1997 | Identical |
| NBN EN 1636-5 : 1997 | Identical |
| UNI EN 1636-5 : 1999 | Identical |
| NS EN 1636-5 : 1ED 1997 | Identical |
| NEN EN 1636-5 : 1997 | Identical |
| BS EN 1636-3:2001 | Plastics piping systems for non-pressure drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) Fittings |
| BS EN 1636-6:2001 | Plastics piping systems for non-pressure drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) Practices for installation |
| EN 1636-3 : 1997 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - PART 3: FITTINGS |
| EN 1450:1996/A1:1998 | PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) COMPONENTS - TEST METHODS TO PROVE THE DESIGN OF BOLTED FLANGE JOINTS |
| EN 1448 : 1996 | PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) COMPONENTS - TEST METHODS TO PROVE THE DESIGN OF RIGID LOCKED SOCKET-AND-SPIGOT JOINTS WITH ELASTOMERIC SEALS |
| EN 1449 : 1996 | PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) COMPONENTS - TEST METHODS TO PROVE THE DESIGN OF CEMENTED SOCKET-AND-SPIGOT JOINTS |
| EN 1119:2009 | Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements |
| EN 1636-3 : 1997 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - PART 3: FITTINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.