EN 1803:2002

Withdrawn

Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Transportable gas cylinders - Periodic inspection and testing of welded carbon steel gas cylinders

Available format(s):

Withdrawn date: 23-07-2013

Language(s):

Published date: 20-02-2002

Publisher: Comite Europeen de Normalisation

Pure ENs are not available for sale, please purchase a suitable national adoption

Table of Contents - (Show below) - (Hide below)

Foreword
Introduction
1 Scope
2 Normative references
3 Intervals between periodic inspection and test
4 List of procedures for periodic inspection and test
5 Identification of cylinder and preparation for
   inspection and test
6 External visual inspection
7 Internal visual inspection
8 Supplementary tests
9 Inspection of cylinder neck
10 Pressure test
11 Repair of cylinders
12 Inspection of valve
13 Final operations
14 Rejection and rendering cylinder unserviceable
Annex A (informative) Gas cylinders manufactured
        according to National Regulations
Annex B (normative) Inspection periods
Annex C (normative) Description, evaluation of defects
        and conditions for rejection of welded carbon
        steel gas cylinders at time of visual inspection
Annex D (normative) Procedure to be adopted when a
        cylinder valve is suspected to be obstructed
Annex E (normative) Proof pressure test of gas cylinders
Annex F (informative) Inspection and maintenance of
        valves and their connections: recommended
        procedures
Annex G (informative) List of commonly used gases
        corrosive to cylinder material
Bibliography

Abstract - (Show below) - (Hide below)

This European Standard specifies the requirements for periodic inspection and testing of welded, carbon steel transportable gas cylinders intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l.NOTE As far as practicable, this standard may also be applied to cylinders of less than 0,5 l water capacity.This Standard specifies the requirements for periodic inspection and testing to verify the integrity of such gas cylinders to be reintroduced into service for a further period of time. It also defines a procedure to qualify existing gas cylinders for free movement between member states of the European Union (see annex A).This standard does not apply to periodic inspection and testing of acetylene cylinders or composite (fully wrapped or hoop-wrapped) steel cylinders.This standard is primarily for industrial gases other than LPG but may also be applied for LPG. However for dedicated LPG cylinders, see EN 1440, Transportable refillable welded steel cylinders for liquefied petroleum gas (LPG) - Periodic requalification prepared by CEN/TC 286 - Liquefied petroleum gas equipment and accessories.

General Product Information - (Show below) - (Hide below)

Committee	CEN/TC 23
Document Type	Standard
ISBN
Pages
Published
Publisher	Comite Europeen de Normalisation
Status	Withdrawn

National Adoptions - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
UNI EN 1803 : 2004	Identical
NEN EN 1803 : 2002	Identical
UNE-EN 1803:2003	Identical
SN EN 1803 : 2002	Identical
NF EN 1803 : 2002	Identical
NBN EN 1795 : 1998	Identical
NBN EN 1803 : 2002	Identical
NS EN 1803 : 1ED 2002	Identical
I.S. EN 1803:2002	Identical
PN EN 1803 : 2002	Identical
BS EN 1803:2002	Identical
DIN EN 1803:2002-09	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

I.S. EN 14189:2003	TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS
I.S. EN 14638-3:2010	TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS
DIN EN ISO 11621:2008-06	GAS CYLINDERS - PROCEDURES FOR CHANGE OF GAS SERVICE
I.S. EN ISO 11621:2005	GAS CYLINDERS - PROCEDURES FOR CHANGE OF GAS SERVICE
DIN EN 14638-3:2012-06	Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 3: Welded carbon steel cylinders made to a design justified by experimental methods (includes Corrigendum AC:2012)
BS EN 14638-3:2010	Transportable gas cylinders. Refillable welded receptacles of a capacity not exceeding 150 litres Welded carbon steel cylinders made to a design justified by experimental methods
EN 14189:2003	Transportable gas cylinders - Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders
UNI EN ISO 11621 : 2006	GAS CYLINDERS - PROCEDURES FOR CHANGE OF GAS SERVICE
UNI EN 14638-3 : 2010	TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS
ISO 11621:1997	Gas cylinders Procedures for change of gas service
BS EN 14189:2003	Transportable gas cylinders. Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders
BS EN 14638-1:2006	Transportable gas cylinders. Refillable welded receptacles of a capacity not exceeding 150 litres Welded austenitic stainless steel cylinders made to a design justified by experimental methods
BS EN ISO 11621:2005	Gas cylinders. Procedures for change of gas service
EN 14638-1:2006	Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 1: Welded austenitic stainless steel cylinders made to a design justified by experimental methods
EN ISO 11621:2005	Gas cylinders - Procedures for change of gas service (ISO 11621:1997)
EN 14638-3:2010/AC:2012	TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS
NF EN 14638-3 : 2010	TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL, CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS
UNE-EN 14638-3:2011	Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 3: Welded carbon steel cylinders made to a design justified by experimental methods
DIN EN 14189:2003-09	TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS
DIN EN 14638-1:2006-07	Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 1: Welded austenitic stainless steel cylinders made to a design justified by experimental methods

Standards Referencing This Book - (Show below) - (Hide below)

EN 629-2 : 1996	TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - GAUGE INSPECTION
ISO 11114-1:2012	Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
PREN 14189 : DRAFT 2001	TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS
EN 1089-1 : 1996	TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - STAMPMARKING
ISO 13341:2010	Gas cylinders — Fitting of valves to gas cylinders
EN ISO 11114-1:2012/A1:2017	GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 1: METALLIC MATERIALS (ISO 11114-1: 2012/AMD 1:2017)
EN 1795 : 1997	TRANSPORTABLE GAS CYLINDERS (EXCLUDING LPG) - PROCEDURES FOR CHANGE OF GAS SERVICE
PREN 13322-2 : DRAFT 1998	TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STAINLESS STEEL GAS CYLINDERS- DESIGN AND CONSTRUCTION - WELDED STAINLESS STEEL
PREN 13322-1 : DRAFT 1998	TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - WELDED STEEL
ISO 11114-2:2013	Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials
EN ISO 13341:2010/A1:2015	Gas cylinders - Fitting of valves to gas cylinders - Amendment 1 (ISO 13341:2010/Amd 1:2015)
EN ISO 11114-2:2013	Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013)
EN 1089-3:2011	Transportable gas cylinders - Gas cylinder identification (excluding LPG) - Part 3: Colour coding
EN 849:1996/A2:2001	TRANSPORTABLE GAS CYLINDERS - CYLINDER VALVES - SPECIFICATION AND TYPE TESTING
EN 837-1:1996/AC:1998	PRESSURE GAUGES - BOURDON TUBE PRESSURE GAUGES - DIMENSIONS, METROLOGY, REQUIREMENTS AND TESTING
EN 1089-2 : 2002	TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - PART 2: PRECAUTIONARY LABELS
EN 837-3:1996	Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart