• EN 60352-5:2012/AC:2014

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    SOLDERLESS CONNECTIONS - PART 5: PRESS-IN CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE (IEC 60352-5:2012)

    Available format(s): 

    Superseded date:  19-09-2020

    Language(s): 

    Published date:  12-01-2013

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    FOREWORD
    INTRODUCTION
    1 Scope and object
    2 Normative references
    3 Terms and definitions
    4 Requirements
    5 Tests
    Annex A (informative) - Practical guidance
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Pertains to solderless press-in connections for use in telecommunication equipment and in electronic devices employing similar techniques.

    General Product Information - (Show below) - (Hide below)

    Committee SR 48B
    Development Note Supersedes UNE EN 60352-5. (03/2011)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 61076-4-102:1997 (published 1997-10) Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part single-pole connectors, for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917
    BS EN 61076-4-115:2003 (published 2003-10) Connectors for electronic equipment. Printed board connectors with assessed quality Backplane connector for InfiniBand equipment
    NF EN 61076 4 100 : 2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2,5 MM FOR PRINTED BOARDS AND BACKPLANES
    BS EN 61076-4-101 : 2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BACKPLANES IN ACCORDANCE WITH IEC 60917
    I.S. EN 61076-4-111:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS WITH ASSESSED QUALIFY - DETAIL SPECIFICATION FOR TWO-PART POWER CONNECTOR MODULES, FOR PRINTED BOARDS AND BACKPLANES HAVING EARLY MATING FEATURES, AND HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1
    UNE-EN 50467:2012 Railway applications - Rolling stock - Electrical connectors, requirements and test methods
    BS EN 61076-4-116 : 2012 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 4-116: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR A HIGH-SPEED TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION
    I.S. EN 50467:2011 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    I.S. EN 62852:2015 CONNECTORS FOR DC-APPLICATION IN PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
    BS EN 50548 : 2011 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    CEI EN 61076-4-111 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-111: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART POWER CONNECTOR MODULES, FOR PRINTED BOARDS AND BACKPLANES HAVING EARLY MATING FEATURES, AND HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1
    I.S. EN 50548:2011 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    I.S. EN 61076-4-103:1999 CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2.5 MM
    EN 61076-4-108 : 2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR CABLE-TO-BOARD CONNECTORS, WITH A MODULAR PITCH OF 25 MM AND INTEGRATED SHIELDING FUNCTION, APPLICABLE FOR TRANSVERSE PACKING DENSITY OF 15 MM, HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1
    EN 61076-4-101 : 2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BACKPLANES IN ACCORDANCE WITH IEC 60917 (IEC 61076-4-101:2001)
    EN 61076-4-114 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM
    EN 61076-4-103 : 1999 CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2.5 MM
    EN 61076-4-102 : 1997 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917
    EN 61076-4-113 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS - PART 4-113: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS HAVING 5 ROWS WITH A GRID OF 2,54 MM FOR PRINTED BOARDS AND BACKPLANES IN BUS APPLICATIONS
    EN 61076-4-110 : 2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION
    I.S. EN 61076-4:1998 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION - PRINTED BOARD CONNECTORS
    12/30235292 DC : 0 BS EN 50343 - RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
    CEI EN 61076-4-110 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION
    BS EN 61076-4-103:1999 (published 1999-06) Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part connectors with shielding and a basic grid of 2,5 mm - Cable to board connectors, shielded against EMC ,grid 2,5 mm,for high speed data rates,for use with printed boards
    BS EN 61076-4-104:1999 (published 1999-08) Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm - Detail specification for two part modular connectors (with optional shielding plates) for printed boards and backplanes, basic grid 2,0 mm, with terminations on a multiple grid of 0,5 mm
    CEI EN 50467 : 2013 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    BS EN 61076-4-113:2003 (published 2003-03) Connectors for electronic equipment Printed board connectors with assessed quality Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications
    PREN 50467 : DRAFT 2009 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    CEI EN 61076-4-115 : 2004 CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-115: PRINTED BOARD CONNECTORS BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT
    BS EN 60352-1 : 1998 SOLDERLESS CONNECTIONS - PART 1: WRAPPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
    I.S. EN 60947-7-4:2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013 (EQV))
    CEI EN 50343 : 2015 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
    BS EN 60603-7 : 2009 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS
    UNE-EN 62852:2015 Connectors for DC-application in photovoltaic systems - Safety requirements and tests
    EN 60603-7:2009/A1:2011 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008/A1:2011)
    CEI EN 61076-4-100 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2,5 MM FOR PRINTED BOARDS AND BACKPLANES
    CEI EN 61076-4 : 1997 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION PRINTED BOARD CONNECTORS
    CEI EN 61076-4-114 : 2004 CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM
    CEI EN 61076-4-108 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-108: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR CABLE-TO-BOARD CONNECTORS, WITH A MODULAR PITCH OF 25 MM AND INTEGRATED SHIELDING FUNCTION, APPLICABLE FOR TRANSVERSE PACKING DENSITY OF 15 MM, HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1
    DD CLC/TS 50467 : 2008 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    I.S. EN 61076-4-113:2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS - PART 4-113: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS HAVING 5 ROWS WITH A GRID OF 2,54 MM FOR PRINTED BOARDS AND BACKPLANES IN BUS APPLICATIONS
    BS EN 50343 : 2014 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
    BS EN 61243-5 : 2001 LIVE WORKING - VOLTAGE DETECTORS - PART 5: VOLTAGE DETECTING SYSTEMS (VDS)
    EN IEC 61076-2-111 : 2018 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-111: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR POWER CONNECTORS WITH M12 SCREW-LOCKING (IEC 61076-2-111:2017)
    I.S. EN 61076-4-102:1998 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917
    BS EN 50173-1:2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
    EN 50173-1:2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
    I.S. EN 61076-3-104:2017 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ
    I.S. EN 61984:2009 CONNECTORS - SAFETY REQUIREMENTS AND TESTS
    S.R. CLC/TS 50467:2008 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    UNE-EN 50521:2010 Connectors for photovoltaic systems - Safety requirements and tests
    EN 61076-4:1996 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION - PRINTED BOARD CONNECTORS
    CEI EN 61076-4-103 : 2001 CONNECTORS FOR USE IN D.C. LOW - FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2,5 MM
    CEI EN 60947-7-4 : 2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS
    BS EN 61076-4-111:2002 (published 2002-08) Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part power connector modules, for printed boards and backplanes having early mating features, and having a basic grid of 2,5 mm in accordance with IEC 60917-1
    BS EN 50467:2011 Railway applications. Rolling stock. Electrical connectors, requirements and test methods
    I.S. EN 61076-4-115:2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-115: PRINTED BOARD CONNECTORS - BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT
    UNE-EN 60947-7-4:2014 Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors
    EN IEC 61076-3-119 : 2018 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-119: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR SHIELDED AND UNSHIELDED, FREE AND FIXED 10-WAY CONNECTORS WITH PUSH-PULL COUPLING FOR INDUSTRIAL ENVIRONMENTS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 100 MHZ (IEC 61076-3-119:2017)
    BS EN 61076-4-110:2002 (published 2002-03) Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function
    BS EN 61076-4-108:2002 (published 2003-06) Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for cable-to-board connectors, with a modular pitch of 25 mm and integrated shielding function, applicable for transverse packing density of 15 mm, having a basic grid of 2,5 mm in accordance with IEC 60917-1
    I.S. EN 60603-7:2009 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008)
    I.S. EN 61076-4-116:2012 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 4-116: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR A HIGH-SPEED TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION
    I.S. EN 61076-4-110:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION
    BS EN 60947-7-4:2013 (published 2013-10) Low-voltage switchgear and controlgear Ancillary equipment. PCB terminal blocks for copper conductors
    CEI EN 60352-1 : 1998 SOLDERLESS CONNECTIONS - PART 1: WRAPPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
    I.S. EN 50343:2014 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
    I.S. EN 61076-4-104:1999 CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GRID OF 2.0 MM WITH TERMINATIONS ON A MULTIPLE GRID OF 0.5 MM
    EN 61076-4-116:2012/A1:2016 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 4-116: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR A HIGH-SPEED TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION (IEC 61076-4-116:2012/A1:2015)
    BS EN 61984 : 2009 CONNECTORS - SAFETY REQUIREMENTS AND TESTS
    EN 62852:2015 CONNECTORS FOR DC-APPLICATION IN PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS (IEC 62852:2014)
    BS EN 50521 : 2009 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
    08/30179116 DC : DRAFT MAR 2008 BS EN 50521 - CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
    CLC/TS 50467 : 2008 COR 2008 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    I.S. EN 61076-4-114:2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM
    I.S. EN 50173-1:2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
    09/30208429 DC : 0 BS EN 50467 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    BS EN 61076-4-107:2001 (published 2001-11) Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations
    CEI EN 61076-4-102 : 1998 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917
    09/30210077 DC : 0 BS EN 50173-1/PRAB - INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEM - PART 1: GENERAL REQUIREMENTS
    BS EN 61076-3-104 : 2017 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ (IEC 61076-3-104:2017)
    CEI EN 50173-1 : 2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
    I.S. EN 61076-4-101:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BACKPLANES IN ACCORDANCE WITH IEC 60917
    BS EN 61076-4-100:2002 (published 2002-01) Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes
    BS EN 61076-4-114:2003 (published 2003-06) Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part connector with integrated shielding function having a grid of 1 mm x 1,5 mm
    I.S. EN 50521:2008 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
    I.S. EN IEC 61076-3-119:2018 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-119: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR SHIELDED AND UNSHIELDED, FREE AND FIXED 10-WAY CONNECTORS WITH PUSH-PULL COUPLING FOR INDUSTRIAL ENVIRONMENTS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 100 MHZ
    I.S. EN IEC 61076-2-111:2018 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-111: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR POWER CONNECTORS WITH M12 SCREW-LOCKING
    I.S. EN 61076-4-108:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-108: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR CABLE-TO-BOARD CONNECTORS, WITH A MODULAR PITCH OF 25 MM AND INTEGRATED SHIELDING FUNCTION, APPLICABLE FOR TRANSVERSE PACKING DENSITY OF 15 MM, HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1
    EN 61076-3-104:2017 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ (IEC 61076-3-104:2017)
    EN 50548 : 2011 AMD 2 2014 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    EN 61076-4-100 : 2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2.5 MM FOR PRINTED BOARDS AND BACKPLANES
    EN 61076-4-115 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-115: PRINTED BOARD CONNECTORS - BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT
    EN 50521:2008/A1:2012 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
    EN 61984:2009 CONNECTORS - SAFETY REQUIREMENTS AND TESTS
    EN 61076-4-107 : 2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-107: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR SHIELDED TWO-PART CONNECTORS HAVING A BASIC GRID OF 2,0 MM, FIXED PART WITH SOLDER AND PRESS-IN TERMINATIONS FOR PRINTED BOARDS, FREE PART WITH NON-ACCESSIBLE INSULATION DISPLACEMENT AND CRIMP TERMINATIONS
    EN 50467 : 2011 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
    EN 50343 : 2014 AMD 1 2017 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
    EN 61076-4-104 : 1999 CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GRID OF 2.0 MM WITH TERMINATIONS ON A MULTIPLE GRID OF 0.5 MM
    EN 60947-7-4 : 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013)

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC GUIDE 109:2012 Environmental aspects - Inclusion in electrotechnical product standards
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    EN 60512-1-100:2012 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 1-100: GENERAL - APPLICABLE PUBLICATIONS (IEC 60512-1-100:2012)
    EN 60068-1:2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    EN 61188-5-1 : 2002 PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES - DESIGN AND USE - PART 5-1: ATTACHMENT (LAND/JOINT) CONSIDERATIONS - GENERIC REQUIREMENTS
    IEC 62326-4:1996 Printed boards - Part 4: Rigid multilayer printed boards with interlayer connections - Sectional specification
    IEC 60352-1:1997 Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance
    IEC 60512-1-100:2012 Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
    IEC 61188-5-1:2002 Printed boards and printed board assemblies - Design and use - Part 5-1: Attachment (land/joint) considerations - Generic requirements
    EN 60352-1 : 1997 SOLDERLESS CONNECTIONS - WRAPPED CONNECTION - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
    EN 62326-4 : 1997 PRINTED BOARDS - RIGID MULTILAYER PRINTED BOARDS WITH INTERLAYER CONNECTIONS - SECTIONAL SPECIFICATION
    IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective