Customer Support: +353 (0)1 857 6730

Corporate Website About Us
  • Shopping Cart
    There are no items in your cart
Please enter a keyword to search
Advanced search
Home
CENELEC
EN 60793-1-31:2010

EN 60793-1-31:2010

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Optical fibres - Part 1-31: Measurement methods and test procedures - Tensile strength

Superseded date

01-02-2022

Superseded by

EN IEC 60793-1-31:2019

Published date

24-09-2010

Publisher

European Committee for Standards - Electrical

Sorry this product is not available in your region.

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Apparatus
4 Sample preparation
5 Procedure
6 Calculations
7 Results
8 Specification information
Annex A (informative) - Typical dynamic testing apparatus
Annex B (informative) - Guideline on gripping the fibre
Annex C (informative) - Guideline on stress rate
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications
Bibliography

IEC 60793-1-31:2010(E) provides values of the tensile strength of optical fibre samples and establishes uniform requirements for the mechanical characteristic - tensile strength. The method tests individual lengths of uncabled and unbundled glass optical fibre. Sections of fibre are broken with controlled increasing stress or strain that is uniform over the entire fibre length and cross section. The stress or strain is increased at a nominally constant rate until breakage occurs. The main change with respect to the previous edition is the addition of comprehensive details, such as examples of fibre clamping as given in Annexes A, B and C.

Committee
CLC/TC 86A
DevelopmentNote
Partially supersedes EN 188000 (07/2002) Supersedes UNE EN 188000. (01/2012)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy
Supersedes

BS EN 60793-2-20:2016 Optical fibres Product specifications. Sectional specification for category A2 multimode fibres
EN 60793-2-30:2015 Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres
EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
EN 60793-2-20:2016 Optical fibres - Part 2-20: Product specifications - Sectional specification for category A2 multimode fibres
EN 60793-2-60:2008 Optical fibres - Part 2-60: Product specifications - Sectional specification for category C single-mode intraconnection fibres
UNE-EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
BS EN 61757-1-1:2017 Fibre optic sensors Strain measurement. Strain sensors based on fibre Bragg gratings
BS EN 60793-2-60:2008 Optical fibres Product specifications. Sectional specification for category C single-mode intraconnection fibres
BS EN 60793-1-1:2017 Optical fibres Measurement methods and test procedures. General and guidance
BS EN 60793-2-30:2015 Optical fibres Product specifications. Sectional specification for category A3 multimode fibres
BS EN 60793-2-50:2016 Optical fibres Product specifications. Sectional specification for class B single-mode fibres
UNE-EN 60793-1-50:2015 Optical fibres - Part 1-50: Measurement methods - Damp heat (steady state) tests
CEI EN 60793-2-60 : 2009 OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES
I.S. EN 60793-2-50:2016 OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES
CEI EN 60793-2-30 : 2016 OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES
EN 61757-1-1:2017 Fibre optic sensors – Part 1-1: Strain measurement – Strain sensors based on fibre Bragg gratings
BS EN 60794-3-11:2010 Optical fibre cables Outdoor cables. Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables
CEI EN 60793-1-1 : 2010 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
BS EN 60793-1-50:2015 Optical fibres Measurement methods. Damp heat (steady state) tests
EN 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
BS EN 60793-2-10:2017 Optical fibres Product specifications. Sectional specification for category A1 multimode fibres
EN 3745-502:2005 Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 502: Tensile stength for short length of optical fibres
I.S. EN 60793-2-10:2017 OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRE
I.S. EN 60793-1-50:2015 OPTICAL FIBRES - PART 1-50: MEASUREMENT METHODS - DAMP HEAT (STEADY STATE) TESTS
I.S. EN 60793-2-60:2008 OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES
I.S. EN 60793-2-30:2015 OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES
I.S. EN 60793-1-1:2017 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
BS EN 3745-502:2005 Aerospace series. Fibres and cables, optical, aircraft use. Test methods Tensile strength for short length of optical fibres
EN 60794-3-11:2010 Optical fibre cables - Part 3-11: Outdoor cables - Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables
EN 60793-2-50:2016 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
EN 60793-1-50:2015 Optical fibres - Part 1-50: Measurement methods and test procedures - Damp heat (steady state) tests

EN 60793-1-21:2002 Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry
EN 60793-1-20:2014/AC:2016-03 OPTICAL FIBRES - PART 1-20: MEASUREMENT METHODS AND TEST PROCEDURES - FIBRE GEOMETRY (IEC 60793-1-20:2014/COR1:2016)
IEC 61649:2008 Weibull analysis
IEC TR 62048:2014 Optical fibres - Reliability - Power law theory
IEC 60793-1-21:2001 Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry
IEC 60793-1-20:2014 Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Get in touch with us