• EN 60832:1996

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Insulating poles (insulating sticks) and universal tool attachments (fittings) for live working

    Available format(s): 

    Superseded date:  01-03-2010

    Language(s): 

    Published date:  17-06-1996

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 Scope
    2 Definitions
    2.1 IEV definitions
    2.2 Definitions of special terms used in this standard
    Chapter I: Insulating poles with permanently attached
                  fittings
    Section one - Technical characteristics
    3 General
    4 Insulation
    5 Dimensional and mechanical characteristics
    6 Ends of insulating poles (sticks)
    6.1 Mechanical protection
    6.2 Corrosion protection
    6.3 Conducting parts
    7 Multiple tubes or rod tools
    Section two - Type tests
    8 General
    9 Visual inspection
    10 Dimensional check
    11 Mechanical tests
    11.1 Torsion
    11.2 Tension
    11.3 Compression
    11.4 Bending
    12 Dye penetration test
    13 Electrical test after water conditioning
    14 Tie pole (tie stick)
    15 Safety hook pole (retractable hook stick)
    16 Hook pole extension (retractable hook stick
          extension)
    17 Universal hand pole (universal hand stick) and
          extendable universal hand pole (stick)
    18 Wire holding pole (wire holding stick)
    19 Cotter-key plier pole
    20 Insulated oiler pole (insulated oiler stick)
    21 Wire-cutter
    22 Measuring pole or rod (stick)
    23 Tension puller (dead-end tool)
    Section three - Routine tests, quality assurance plan
          and acceptance tests
    24 Sampling tests
    25 Routine tests
    Chapter II: Universal tool attachments (fittings)
    Section four - Technical characteristics common to all
                    tool attachments
    26 General
    27 Dimensional and mechanical characteristics
    28 Mechanical protection
    29 Corrosion protection
    30 Conducting attachments
    Section five - Type tests
    31 General
    32 Visual inspection
    33 Dimensional check
    34 Compatibility check
    35 Hook pole adapter (retractable hook stick adapter)
          and universal adapter
    36 Formed wire tool
    37 Locating pin (locating drift)
    38 Conductor cleaning brush: semi-tubular type
    39 Conductor cleaning brush: V-shaped type
    40 Oilcan
    41 Ratchet spanner (ratchet wrench)
    42 Spanner (wrench)
    43 Split-pin remover (cotter-key installer remover)
    44 Holding fork
    45 Split-pin installer remover (cotter-key installer
          remover)
    46 Binding wire-cutter (tie wire-cutter)
    47 Rotary blade
    48 Rotary prong
    49 Adjustable pliers
    50 Vice-grip pliers
    51 Adjustable insulator fork
    52 All-angle pliers
    53 Pin-holder
    54 Flexible spanner head (flexible wrench head)
    55 Ammeter holder
    56 Anti-interference braid applicator
    57 Hack saw
    58 Mirror
    59 Conductor (wire) gauge
    60 Gap gauge
    61 Clevis and tenon pole tools (clevis and tongue
          tools)
    Section six - Routine tests, quality assurance plan
          and acceptance tests
    62 Sampling tests
    63 Routine tests
    Chapter III: Special clauses
    64 Marking
    65 Modifications
    66 Acceptance tests
    Appendices
    A Acceptance test
    B Insulating poles with permanently attached
          fittings - Figures
    C Universal tool attachments (fittings) - Figures
    D Splined ends of poles and attachments - Examples
    E Abrasion resistance test - Technical data
    ZA Normative references to international publications
          with their corresponding European publications

    Abstract - (Show below) - (Hide below)

    Applies to insulating poles (insulating sticks), and tool attachments (fittings) and is divided into three chapters. Chapter I: Specifies the required characteristics for insulating poles with permanently attached fittings and the tests (electrical and mechanical) which should be satisfied by these tools. Chapter II: Specifies the required characteristics for parts which may be attached to and detached from the ends of poles described in Chapter I, and the tests which should be satisfied by these tools. Chapter Ill: Specifies the special clauses, applicable to insulating poles and universal tool attachments.

    General Product Information - (Show below) - (Hide below)

    Committee CLC/TC 78
    Development Note SUPERSEDES HD 542 (05/2001)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    CEI EN 62193 : 2005 LIVE WORKING - TELESCOPIC STICKS AND TELESCOPIC MEASURING STICKS
    CEI EN 50508 : 2009 MULTI-PURPOSE INSULATING STICKS FOR ELECTRICAL OPERATIONS ON HIGH VOLTAGE INSTALLATIONS
    EN 61230:2008 LIVE WORKING - PORTABLE EQUIPMENT FOR EARTHING OR EARTHING AND SHORT-CIRCUITING
    BS EN 50508:2009 Multi-purpose insulating sticks for electrical operations on high voltage installations
    BS EN 62193:2003 Live working. Telescopic sticks and telescopic measuring sticks
    I.S. EN 50508:2009 MULTI-PURPOSE INSULATING STICKS FOR ELECTRICAL OPERATIONS ON HIGH VOLTAGE INSTALLATIONS
    CLC/TR 50488:2006 Railway applications - Safety measures for the personnel working on or near overhead contact lines
    I.S. EN 62193:2003 LIVE WORKING - TELESCOPIC STICKS AND TELESCOPIC MEASURING STICKS
    CEI CLC/TR 50488 : 2007 RAILWAY APPLICATIONS - SAFETY MEASURES FOR PERSONNEL WORKING NEAR OVERHEAD CONTACT LINES
    UNE-EN 50508:2011 Multi-purpose insulating sticks for electrical operations on high voltage installations
    BS EN 61230:2008 Live working. Portable equipment for earthing or earthing and short-circuiting
    S.R. CLC/TR 50488:2007 RAILWAY APPLICATIONS - SAFETY MEASURES FOR THE PERSONNEL WORKING ON OR NEAR OVERHEAD CONTACT LINES
    06/30159668 DC : 0 BS EN 50508 - MULTI-PURPOSE INSULATING STICKS FOR ELECTRICAL OPERATIONS ON HIGH VOLTAGE INSTALLATIONS
    EN 50508:2009 Multi-purpose insulating sticks for electrical operations on high voltage installations
    EN 62193:2003 Live working - Telescopic sticks and telescopic measuring sticks

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60212:2010 Standard conditions for use prior to and during the testing of solid electrical insulating materials
    IEC 60855:1985 Insulating foam-filled tubes and solid rods for live working
    BS 3939-2:1985 Graphical symbols for electrical power, telecommunications and electronics diagrams Symbol elements, qualifying symbols and other symbols having general application
    IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
    HD 437 : 200S1 STANDARD CONDITIONS FOR USE PRIOR TO AND DURING THE TESTING OF SOLID ELECTRICAL INSULATING MATERIALS
    IEC 60743:2013 Live working - Terminology for tools, devices and equipment
    EN 60743:2013 Live working - Terminology for tools, devices and equipment
    HD 588.1 : S1 AMD 1 HIGH VOLTAGE TEST TECHNIQUES - GENERAL DEFINITIONS AND TEST REQUIREMENTS
    BS 3939-1:1986 Graphical symbols for electrical power, telecommunications and electronics diagrams General information, general index
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    EN 60060-2:2011 High-voltage test techniques - Part 2: Measuring systems
    EN 60855:1996 Insulating foam-filled tubes and solid rods for live working
    BS 3939-3:1985 Graphical symbols for electrical power, telecommunications and electronics diagrams Conductors and connecting devices
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective