Skip to content
Please enter a keyword to search

  • EN 60987:2015

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Nuclear power plants - Instrumentation and control important to safety - Hardware design requirements for computer-based systems

    Available format(s): 

    Superseded date:  25-09-2021

    Language(s): 

    Published date:  20-02-2015

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Project structure
    5 Hardware requirements
    6 Design and development
    7 Verification and validation
    8 Qualification
    9 Manufacture
    10 Installation and commissioning
    11 Maintenance
    12 Modification
    13 Operation
    Annex A (informative) - Overview of system life cycle
    Annex B (informative) - Outline of qualification
    Annex C (informative) - Example of maintenance procedure
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Is applicable to computer-system hardware for systems of Class 1 and 2 (as defined by IEC 61513) in nuclear power plants. This new edition reflects recent developments in computer system hardware design, the use of pre-developed hardware and changes in terminology.

    General Product Information - (Show below) - (Hide below)

    Committee CLC/TC 45AX
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 61226:2010 Nuclear power plants. Instrumentation and control important to safety. Classification of instrumentation and control functions
    EN 60671:2011 Nuclear power plants - Instrumentation and control systems important to safety - Surveillance testing
    EN 62566:2014 Nuclear power plants - Instrumentation and control important to safety - Development of HDL-programmed integrated circuits for systems performing category A functions
    BS EN 61513:2013 Nuclear power plants. Instrumentation and control important to safety. General requirements for systems
    BS EN 60671:2011 Nuclear power plants. Instrumentation and control systems important to safety. Surveillance testing
    EN 61226:2010 Nuclear power plants - Instrumentation and control important to safety - Classification of instrumentation and control functions
    KTA 3505 : 2015(R2017) TYPE TESTING OF MEASURING SENSORS AND TRANSDUCERS OF THE INSTRUMENTATION AND CONTROL SYSTEM IMPORTANT TO SAFETY
    CEI EN 60671 : 2012 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL SYSTEMS IMPORTANT TO SAFETY - SURVEILLANCE TESTING
    I.S. EN 60671:2011 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL SYSTEMS IMPORTANT TO SAFETY - SURVEILLANCE TESTING
    BS EN 62566:2014 Nuclear power plants. Instrumentation and control important to safety. Development of HDL-programmed integrated circuits for systems performing category A functions
    CEI EN 61500 : 2012 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - DATA COMMUNICATION IN SYSTEMS PERFORMING CATEGORY A FUNCTIONS
    CEI EN 61513 : 2013 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - GENERAL REQUIREMENT FOR SYSTEMS
    I.S. EN 61226:2010 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - CLASSIFICATION OF INSTRUMENTATION AND CONTROL FUNCTIONS
    BS EN 61500:2011 Nuclear power plants. Instrumentation and control important to safety. Data communication in systems performing category A functions
    EN 61500:2011 Nuclear power plants - Instrumentation and control important to safety - Data communication in systems performing category A functions
    I.S. EN 62566:2014 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - DEVELOPMENT OF HDL-PROGRAMMED INTEGRATED CIRCUITS FOR SYSTEMS PERFORMING CATEGORY A FUNCTIONS
    I.S. EN 61500:2011 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - DATA COMMUNICATION IN SYSTEMS PERFORMING CATEGORY A FUNCTIONS
    I.S. EN 61513:2013 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - GENERAL REQUIREMENTS FOR SYSTEMS (IEC 61513:2011 (EQV))
    EN 61513:2013 Nuclear power plants - Instrumentation and control important to safety - General requirements for systems

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61025:2006 Fault tree analysis (FTA)
    EN 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
    ISO 3951-1:2013 Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
    EN 22768-2:1993 General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989)
    IEC 61226:2009 Nuclear power plants - Instrumentation and control important to safety - Classification of instrumentation and control functions
    IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
    IEC 62138:2004 Nuclear power plants - Instrumentation and control important for safety - Software aspects for computer-based systems performing category B or C functions
    EN 62138 : 2009 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT FOR SAFETY - SOFTWARE ASPECTS FOR COMPUTER-BASED SYSTEMS PERFORMING CATEGORY B OR C FUNCTIONS
    EN 60880 : 2009 NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL SYSTEMS IMPORTANT TO SAFETY - SOFTWARE ASPECTS FOR COMPUTER-BASED SYSTEMS PERFORMING CATEGORY A FUNCTIONS
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 2768-2:1989 GENERAL TOLERANCES - PART 2: GEOMETRICAL TOLERANCES FOR FEATURES WITHOUT INDIVIDUAL TOLERANCE INDICATIONS
    ISO/IEC 12207:2008 Systems and software engineering Software life cycle processes
    EN 22768-1:1993 General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989)
    EN 61025:2007 Fault tree analysis (FTA)
    IEC 60880:2006 Nuclear power plants - Instrumentation and control systems important to safety - Software aspects for computer-based systems performing category A functions
    ISO 9001:2015 Quality management systems — Requirements
    IEC 60780:1998 Nuclear power plants - Electrical equipment of the safety system - Qualification
    IEC 61513:2011 Nuclear power plants - Instrumentation and control important to safety - General requirements for systems
    ISO 3951-2:2013 Sampling procedures for inspection by variables — Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective