• There are no items in your cart

EN 61207-1:2010

Current

Current

The latest, up-to-date edition.

Expression of performance of gas analyzers - Part 1: General

Published date

30-07-2010

FOREWORD
1 Scope and object
2 Normative references
3 Terms and definitions
4 Procedure for specification
5 Procedure for compliance testing
Annex A (informative) - Recommended standard values of
        influence - Quantities affecting performance from
        IEC 60359
Annex B (informative) - Performance characteristics calculable
        from drift tests
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

IEC 61207-1:2010 specifies the terminology, definitions, requirements for statements by manufacturers and tests that are common to all gas analyzers. It is applicable to analyzers specified for permanent installation in any location (indoors or outdoors) and to such analyzers utilizing either a sample handling system or an in situ measurement technique. It is applicable to the complete analyzer when supplied by one manufacturer as an integral unit, comprised of all mechanical, electrical and electronic portions. It also applies to sensor units alone and electronic units alone when supplied separately or by different manufacturers. This second edition cancels and replaces the first edition published in 1994 and constitutes a technical revision. The significant technical changes with respect to the first edition are the following:
- all references (normative and informative) have been updated, deleted or added, as appropriate;
- all the terms and definitions relating to this International Standard have been updated;
- all references to 'errors' have been replaced by 'uncertainties' and appropriate updated definitions applied.
Where only one value is quoted for a performance specification, such as intrinsic uncertainty, linearity uncertainty or repeatability throughout a measurement range, this has now been defined as the maximum value, rather than an average or 'representative' value. This was previously undefined. Where zero and 100 % span calibration gases are used, there is now a defined requirement that the analyser must be able to respond within its standard performance specifications beyond its normal measurement range, to allow for any under or over response of the instrument to be recorded. A new Annex A has been added giving recommended standard values of influence.

Committee
CLC/TC 65X
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Current

BS EN 61207-7:2013 Expression of performance of gas analyzers Tuneable semiconductor laser gas analyzers
EN 61207-6:2015 Expression of performance of gas analyzers - Part 6:Photometric analyzers
BS EN 61207-6:2015 Expression of performance of gas analyzers Photometric analyzers
I.S. EN 61207-7:2013 EXPRESSION OF PERFORMANCE OF GAS ANALYZERS - PART 7: TUNEABLE SEMICONDUCTOR LASER GAS ANALYZERS
I.S. EN 61207-3:2002 GAS ANALYZERS - EXPRESSION OF PERFORMANCE - PARAMAGNETIC OXYGEN ANALYZERS
I.S. EN 61207-2:1995 EXPRESSION OF PERFORMANCE OF GAS ANALYZERS - PART 2: OXYGEN IN GAS (UTILIZING HIGH-TEMPERATURE ELECTROCHEMICAL SENSORS)
CEI EN 61207-6 : 2016 EXPRESSION OF PERFORMANCE OF GAS ANALYZERS - PART 6: PHOTOMETRIC ANALYZERS
BS EN 61207-3:2002 Expression of performance of gas analyzers Paramagnetic oxygen analyzers
I.S. EN 61207-6:2015 EXPRESSION OF PERFORMANCE OF GAS ANALYZERS - PART 6: PHOTOMETRIC ANALYZERS
EN 61207-7:2013/AC:2015 EXPRESSION OF PERFORMANCE OF GAS ANALYZERS - PART 7: TUNEABLE SEMICONDUCTOR LASER GAS ANALYZERS (IEC 61207-7:2013)
EN 61207-2:1994 Expression of performance of gas analyzers - Part 2: Oxygen in gas (utilizing high-temperature electrochemical sensors)
EN 61207-3:2002 Gas analyzers - Expression of performance - Part 3: Paramagnetic oxygen analyzers

ISO 6144:2003 Gas analysis Preparation of calibration gas mixtures Static volumetric method
IEC 60381-1:1982 Analogue signals for process control systems. Part 1: Direct current signals
EN ISO 6142:2006 Gas analysis - Preparation of calibration gas mixtures - Gravimetric method (ISO 6142:2001)
IEC 61207-2:1994 Expression of performance of gas analyzers - Part 2: Oxygen in gas (utilizing high-temperature electrochemical sensors)
EN 60359:2002 Electrical and electronic measurement equipment - Expression of performance
EN 60382 : 93 AC 94 ANALOGUE PNEUMATIC SIGNAL FOR PROCESS CONTROL SYSTEMS
IEC 61187:1993 Electrical and electronic measuring equipment - Documentation
ISO 16664:2017 Gas analysis — Handling of calibration gases and gas mixtures — Guidelines
EN ISO 6143:2006 Gas analysis - Comparison methods for determining and checking the composition of calibration gas mixtures (ISO 6143:2001)
EN ISO 16664:2017 Gas analysis - Handling of calibration gases and gas mixtures - Guidelines (ISO 16664:2017)
ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
ISO 6143:2001 Gas analysis — Comparison methods for determining and checking the composition of calibration gas mixtures
ISO 31-0:1992 Quantities and units Part 0: General principles
HD 452.1 : 200S1 ANALOGUE SIGNALS FOR PROCESS CONTROL SYSTEMS - DIRECT CURRENT SIGNALS
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
IEC 60382:1991 Analogue pneumatic signal for process control systems
ISO 6142:2001 Gas analysis Preparation of calibration gas mixtures Gravimetric method
EN 60654-1 : 1993 Industrial-process measurement and control equipment - Operating conditions - Part 1: Climatic conditions
EN ISO 6141:2015 Gas analysis - Contents of certificates for calibration gas mixtures (ISO 6141:2015)
ISO 9001:2015 Quality management systems — Requirements
EN 61207-2:1994 Expression of performance of gas analyzers - Part 2: Oxygen in gas (utilizing high-temperature electrochemical sensors)
EN 61187:1994/corrigendum:1995 ELECTRICAL AND ELECTRONIC MEASURING EQUIPMENT - DOCUMENTATION
IEC 60359:2001 Electrical and electronic measurement equipment - Expression of performance
EN 61010-1:2010 Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
IEC 60654-1:1993 Industrial-process measurement and control equipment - Operating conditions - Part 1: Climatic conditions
ISO/TS 14167:2003 Gas analysis General quality assurance aspects in the use of calibration gas mixtures - Guidelines
ISO 6141:2015 Gas analysis Contents of certificates for calibration gas mixtures
IEC 61010-1:2010+AMD1:2016 CSV Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
IEC 60050-300:2001 International Electrotechnical Vocabulary (IEV) - Part 300: Electrical and electronic measurements and measuring instruments - Part 311: General terms relating to measurements - Part 312: General terms relating to electrical measurements - Part 313: Types of electrical measuring instruments - Part 314: Specific terms according to the type of instrument
EN 60770-1:2011 Transmitters for use in industrial-process control systems - Part 1: Methods for performance evaluation
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
IEC 60770-1:2010 Transmitters for use in industrial-process control systems - Part 1: Methods for performance evaluation
EN ISO 6144:2006 Gas analysis - Preparation of calibration gas mixtures - Static volumetric method (ISO 6144:2003)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.