Skip to content
Please enter a keyword to search

  • EN 61212-2:2006

    Current The latest, up-to-date edition.

    Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test

    Available format(s): 

    Language(s): 

    Published date:  14-12-2006

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Conditioning of specimens
    4 Dimensions
      4.1 General
      4.2 External diameter
      4.3 Internal diameter
      4.4 Wall thickness
      4.5 Departure from straightness - Applicable
          to all tubes up to 300 mm diameter
    5 Mechanical tests
      5.1 Flexural strength perpendicular to laminations
      5.2 Axial compressive strength
      5.3 Cohesion between layers
    6 Electrical tests
      6.1 Electric strength and breakdown voltage
      6.2 Insulation resistance after immersion in water
      6.3 Dissipation factor and permittivity (tube only)
    7 Other tests
      7.1 Thermal endurance
      7.2 Water absorption
      7.3 Density
      7.4 Flammability
    Annex ZA (normative) Normative references to
             international publications with their
             corresponding European publications
    BIBLIOGRAPHY

    Abstract - (Show below) - (Hide below)

    This part of IEC 61212 describes methods of test for the materials defined in IEC 61212-1. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

    General Product Information - (Show below) - (Hide below)

    Committee CLC/SR 15
    Development Note Supersedes UNE EN 61212-2. (11/2009)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    EN 61212-3-2:2013 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Round laminated moulded tubes
    I.S. EN 61212-3-1:2013 INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 1: ROUND LAMINATED ROLLED TUBES (IEC 61212-3-1:2013 (EQV))
    I.S. EN 61212-3-2:2013 INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: ROUND LAMINATED MOULDED TUBES (IEC 61212-3-2:2013 (EQV))
    BS EN 61212-3-1:2013 INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 1: ROUND LAMINATED ROLLED TUBES
    BS EN 61212-3-2:2013 INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: ROUND LAMINATED MOULDED TUBES
    EN 62631-3-2:2016 Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC Methods) - Surface resistance and surface resistivity
    EN 61212-3-1:2013 INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 1: ROUND LAMINATED ROLLED TUBES (IEC 61212-3-1:2013)

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    EN 61212-1:2006 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements
    EN ISO 62:2008 Plastics - Determination of water absorption (ISO 62:2008)
    EN 60216-1:2013 Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results
    IEC 60212:2010 Standard conditions for use prior to and during the testing of solid electrical insulating materials
    IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
    HD 437 : 200S1 STANDARD CONDITIONS FOR USE PRIOR TO AND DURING THE TESTING OF SOLID ELECTRICAL INSULATING MATERIALS
    EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
    EN ISO 604 : 2003 PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES (ISO 604:2002)
    IEC 60216-2:2005 Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria
    EN 60216-2:2005 Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria
    IEC 60167:1964 Methods of test for the determination of the insulation resistance of solid insulating materials
    IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
    ISO 6906:1984 Vernier callipers reading to 0,02 mm
    HD 568 : 200S1 METHODS OF TEST FOR THE DETERMINATION OF THE INSULATION RESISTANCE OF SOLID INSULATING MATERIALS
    ISO 1642:1987 Plastics Industrial laminated sheets based on thermosetting resins Specification
    EN 60296:2012 Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
    ISO 3599:1976 Vernier callipers reading to 0,1 and 0,05 mm
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 604:2002 Plastics — Determination of compressive properties
    EN 60243-1:2013 ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013)
    ISO 3611:2010 Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
    ISO 62:2008 Plastics Determination of water absorption
    IEC 61212-1:2006 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements
    ISO 178:2010 Plastics Determination of flexural properties
    IEC 60216-1:2013 Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results
    EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective