• EN 61264:1998/corrigendum:2000

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    CERAMIC PRESSURIZED HOLLOW INSULATORS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR

    Available format(s): 

    Superseded date:  01-08-2003

    Language(s): 

    Published date:  12-01-2013

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Contents
    Foreword
    Introduction
    Clause
    1. Scope and object
    2. Normative references
    3. Definitions
    4. General recommendations for design and construction
        4.1 Purpose
        4.2 Rules for design
    5. General requirements for tests
        5.1 Classification of tests
        5.2 General requirements for pressure tests
        5.3 General requirements for bending tests
    6. Type tests
        6.1 General
        6.2 Pressure test
        6.3 Bending test
    7. Sample tests
        7.1 Selection and number of test pieces
        7.2 Tests
        7.3 Re-test procedure
        7.4 Verification of dimensions
        7.5 Control of the roughness of ground parts
        7.6 Mechanical test (for assembled hollow insulators)
    8. Routine tests
        8.1 General
        8.2 Mechanical tests
        8.3 Other tests
    9. Documentation
        9.1 Marking
        9.2 Certificates
    Annexes
    A (informative) Tolerances of form and position
    B (informative) Bending moment equivalent to the design
       pressure
    C (informative) Bibliography
    Annex ZA (normative) Normative references to
               international publications
             with their corresponding
             European publications

    Abstract - (Show below) - (Hide below)

    Applicable to hollow insulators made from ceramic material, with their fixing devices, to be used with a permanent gas pressure in excess of 50 kPa gauge with an internal volume equal to or greater than 1 I(1000cm x cm x cm).

    General Product Information - (Show below) - (Hide below)

    Committee SR 36C
    Development Note This Standard supersedes EN 50062:1991 (02/2001) Also numbered as IEC 61264. (06/2001)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    CEI EN 62271-203 : 2013 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 203: GAS-INSULATED METAL-ENCLOSED SWITCHGEAR FOR RATED VOLTAGES ABOVE 52 KV
    08/30179468 DC : DRAFT MAR 2008 BS EN 62271-203 - HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 203: GAS-INSULATED METAL-ENCLOSED SWITCHGEAR FOR RATED VOLTAGES ABOVE 52 KV
    BS EN 45510-2-7 : 2002 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
    CEI UNI EN 45510-2-7 : 2006 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
    BS EN 62271-203:2012 High-voltage switchgear and controlgear Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
    DIN EN 45510-2-7:2003-12 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
    UNI CEI EN 45510-2-7 : 2011 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
    I.S. EN 62271-203:2012 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 203: GAS-INSULATED METAL-ENCLOSED SWITCHGEAR FOR RATED VOLTAGES ABOVE 52 KV (IEC 62271-203:2011 (EQV))
    I.S. EN 45510-2-7:2002 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
    UNE-EN 62271-203:2013 High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
    IEC 62271-203:2011 High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
    EN 62271-203:2012 High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
    EN 45510-2-7 : 2002 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    IEC 60050-471:2007 International Electrotechnical Vocabulary (IEV) - Part 471: Insulators
    IEC 60672-3:1997 CERAMIC AND GLASS-INSULATING MATERIALS - SPECIFICATIONS FOR INDIVIDUAL MATERIALS
    IEC 60056:1987 High-voltage alternating-current circuit-breakers
    IEC 61166 : 1.0 HIGH VOLTAGE ALTERNATING CURRENT CIRCUIT BREAKERS - GUIDE FOR SEISMIC QUALIFICATION OF HIGH VOLTAGE ALTERNATING CIRCUIT BREAKERS
    IEC 60694:1996+AMD1:2000+AMD2:2001 CSV Common specifications for high-voltage switchgear and controlgear standards
    IEC 60865-1:2011 Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods
    EN 50062 : 1991 CERAMIC PRESSURIZED HOLLOW INSULATORS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR
    ISO 4287-2:1984 Surface roughness — Terminology — Part 2: Measurement of surface roughness parameters
    IEC 60168:1994+AMD1:1997+AMD2:2000 CSV Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000 V
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective