Skip to content
Please enter a keyword to search

  • EN ISO 11296-4:2018

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2018)

    Available format(s): 

    Superseded date:  29-06-2021

    Language(s): 

    Published date:  14-02-2018

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    European foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Pipes at the 'M' stage
    6 Fittings at the 'M' stage
    7 Ancillary components
    8 Fitness for purpose of the installed lining
      system at the 'I' stage
    9 Installation practice
    Annex A (informative) - CIPP components and
            their functions
    Annex B (normative) - Cured-in-place pipes -
            Determination of short-term flexural properties
    Annex C (normative) - Cured-in-place pipes -
            Determination of long-term flexural
            modulus under dry or wet conditions
    Annex D (normative) - Cured-in-place pipes -
            Determination of long-term flexural
            strength under dry, wet or acidic conditions
            (stress corrosion test)
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 11296-4:2018, in conjunction with ISO 11296‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks with service temperatures up to 50 °C.ISO 11296-4:2018 applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.3).

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 155
    Development Note Supersedes EN 13566-4. (05/2011)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 8773:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP)
    ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
    ISO 10467:2004 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
    ISO 10928:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
    ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 13002:1998 Carbon fibre Designation system for filament yarns
    ISO 8513:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
    ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
    ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
    ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
    ISO 7684:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the creep factor under dry conditions
    ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
    EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
    ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective