Skip to content
Please enter a keyword to search

  • EN ISO 11298-3:2011

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2010)

    Available format(s): 

    Superseded date:  01-02-2019

    Language(s): 

    Published date:  27-04-2011

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Pipes at the "M" stage
    6 Fittings at the "M" stage
    7 Ancillary components
    8 Fitness for purpose of the installed lining system at
      the "I" stage
    9 Installation practice
    Annex A (normative) - Factory-folded heat-reverted
            polyethylene (PE) pipe - Determination of memory
            ability
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 11298-3:2010, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 155
    Development Note Supersedes EN 14409-3. (05/2011)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 12201-4:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
    ISO 4427-3:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings
    ISO 4427-1:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General
    ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
    ISO 12176-1:2017 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 4427-5:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system
    ISO 12176-2:2008 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 11298-1:2010 Plastics piping systems for renovation of underground water supply networks Part 1: General
    ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
    ISO 4427-2:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective