Skip to content
Please enter a keyword to search

  • EN ISO 11403-1:2014

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014)

    Available format(s): 

    Superseded date:  10-07-2021

    Language(s): 

    Published date:  18-06-2014

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Specimen preparation
    5 Conditioning
    6 Test requirements
    7 Presentation of data
    8 Precision
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 11403-1:2014 specifies test procedures for the acquisition and presentation of multipoint data on the following mechanical properties of plastics:dynamic modulus; tensile properties at constant test speed; ultimate stress and strain; tensile stress-strain curves; tensile creep; Charpy impact strength; puncture impact behaviour.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 249
    Development Note Supersedes PREN ISO 11403-1. (06/2014)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN ISO 10724-1:2001 Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) General principles and moulding of multipurpose test specimens

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6603-2:2000 Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
    ISO 15850:2014 Plastics Determination of tension-tension fatigue crack propagation Linear elastic fracture mechanics (LEFM) approach
    ISO 6721-2:2008 Plastics Determination of dynamic mechanical properties Part 2: Torsion-pendulum method
    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
    ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 17281:2002 Plastics Determination of fracture toughness (GIC and KIC) at moderately high loading rates (1 m/s)
    ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
    ISO 6721-4:2008 Plastics Determination of dynamic mechanical properties Part 4: Tensile vibration Non-resonance method
    ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
    ISO 20753:2008 Plastics Test specimens
    ISO 13586:2000 Plastics Determination of fracture toughness (GIC and KIC) Linear elastic fracture mechanics (LEFM) approach
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 10724-2:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective