Skip to content
Please enter a keyword to search

  • EN ISO 15012-2:2008

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Health and safety in welding and allied processes - Requirements, testing and marking of equipment for air filtration - Part 2: Determination of the minimum air volume flow rate of captor hoods and nozzles (ISO 15012-2:2008)

    Available format(s): 

    Superseded date:  29-03-2022

    Language(s): 

    Published date:  01-04-2008

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Requirement
    6 Equipment
    7 Test method
    8 Marking
    9 Test report
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 15012-2:2008 specifies a method for establishing the minimum air volume flow rate required for captor hoods and nozzles to effectively capture fume and gases from welding and allied processes. The method can be used with capture devices of any aspect ratio and cross-sectional area, but it is not applicable to on-gun extraction systems and down draught tables.ISO 15012-2:2008 also specifies the test data to be marked on the capture devices.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 121
    Development Note Supersedes PREN ISO 15012-2. (02/2009)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    CEN/TR 15339-6:2014 Thermal spraying - Safety requirements for thermal spraying equipment - Part 6: Spray booth, Handling system, Dust collection, Exhaust system, Filter
    PD CEN/TR 15339-6:2014 Thermal spraying. Safety requirements for thermal spraying equipment Spray booth, Handling system, Dust collection, Exhaust system, Filter
    S.R. CEN/TR 15339-6:2014 THERMAL SPRAYING - SAFETY REQUIREMENTS FOR THERMAL SPRAYING EQUIPMENT - PART 6: SPRAY BOOTH, HANDLING SYSTEM, DUST COLLECTION, EXHAUST SYSTEM, FILTER

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 5167-3:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 3: Nozzles and Venturi nozzles
    EN 1093-1:2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods
    ISO 2602:1980 Statistical interpretation of test results Estimation of the mean Confidence interval
    ISO 5167-2:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 2: Orifice plates
    EN 626-2:1996+A1:2008 Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures
    ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
    ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
    ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective