Skip to content
Please enter a keyword to search

  • EN ISO 21258:2010

    Current The latest, up-to-date edition.

    Stationary source emissions - Determination of the mass concentration of dinitrogen monoxide (N2O) - Reference method: Non-dispersive infrared method (ISO 21258:2010)

    Available format(s): 

    Language(s): 

    Published date:  15-06-2010

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Principle
    6 Description of the automated measuring equipment
    7 Performance criteria and determination of the performance
       characteristics
    8 Measurement procedure
    9 Ongoing quality control
    10 Evaluation of the method in the field
    11 Expression of results
    12 Test report
    Annex A (informative) - Schematic diagram of a typical analyser
    Annex B (normative) - Procedures for determination of the
            performance characteristics during the general
            performance test
    Annex C (informative) - Example of assessment of compliance of
            NDIR method for N[2]O with requirements on emission
            measurements
    Annex D (informative) - Results of comparison tests
    Annex E (informative) - Leak test procedures
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 21258:2010 specifies a method for sampling, sample conditioning and determination of dinitrogen monoxide (N2O) content in the flue gas emitted from ducts and stacks to atmosphere. It sets out the non-dispersive infrared (NDIR) analytical technique, including the sampling system and sample gas conditioning system.ISO 21258:2010 is a reference method for periodic monitoring and for calibration, adjustment or control of automatic monitoring systems permanently installed on a stack.This reference method has been successfully tested on a sewage sludge incinerator where the N2O concentration in the flue gas was up to about 200 mg/m3.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 264
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    14/30303591 DC : 0 BS EN ISO 19694-1 - STATIONARY SOURCE EMISSIONS - DETERMINATION OF GREENHOUSE GAS (GHG) EMISSIONS IN ENERGY-INTENSIVE INDUSTRIES - PART 1: GENERAL ASPECTS
    VDI 3477:2016-03 Biological waste gas purification - Biofilters
    15/30318313 DC : 0 BS EN 15267-4 - AIR QUALITY - CERTIFICATION OF AUTOMATED MEASURING SYSTEMS - PART 4: PERFORMANCE CRITERIA AND TEST PROCEDURES FOR AUTOMATED MEASURING SYSTEMS FOR PERIODIC MEASUREMENTS OF EMISSIONS FROM STATIONARY SOURCE

    Standards Referencing This Book - (Show below) - (Hide below)

    VDI 2469 Blatt 2:2005-02 Gaseous emission measurement - Measurement of nitrous oxide - Automatic infrared spectrometric method
    ISO 14956:2002 Air quality Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty
    EN 15259:2007 Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report
    EN 13284-1:2017 Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method
    ISO 3534-2:2006 Statistics Vocabulary and symbols Part 2: Applied statistics
    ISO/TS 21748:2004 Guidance for the use of repeatability, reproducibility and trueness estimates in measurement uncertainty estimation
    ISO 12039:2001 Stationary source emissions Determination of the mass concentration of carbon monoxide, carbon dioxide and oxygen in flue gas Performance characteristics of automated measuring systems
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    ISO 20988:2007 Air quality Guidelines for estimating measurement uncertainty
    EN 14792:2017 Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence
    ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
    ISO 9169:2006 Air quality Definition and determination of performance characteristics of an automatic measuring system
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective