Skip to content
Please enter a keyword to search

  • EN ISO 4759-3:2016

    Current The latest, up-to-date edition.

    Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016)

    Available format(s): 

    Language(s): 

    Published date:  29-06-2016

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 4759-3:2016 specifies tolerances for flat washers of product grades A, C and F with nominal diameters of 1 mm to 150 mm inclusive, designed to be used in bolted joints in combination with bolts, screws, studs and nuts.This part of ISO 4759 may be applied to non-flat washers however it does not include all the tolerances related to these washers.It applies to non-captive and captive washers, and to standard and non-standard washers.It does not apply to dynamic disc springs.Washers of product grades F and A are intended to be used with bolts, screws, studs and nuts of product grades A and B; washers of product grade C are intended to be used with bolts, screws, studs and nuts of product grade C.NOTE The product grade refers to a specific tolerance range related to dimensional and geometrical characteristics (product grade F for fine tolerances, product grade A for precise tolerances, product grade C for large tolerances).Annex A presents tolerances taken from ISO 286‑1 and ISO 286‑2.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 185
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    03/318786 DC : DRAFT NOV 2003 EN 14831 - FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD
    13/30277440 DC : 0 BS EN 14399-6 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS
    I.S. EN ISO 3269:2000 FASTENERS - ACCEPTANCE INSPECTION
    BS EN ISO 7089:2000 Plain washers. Normal series. Product grade A
    07/30107797 DC : 0 BS EN 14399-9 - HIGH STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - BOLT AND NUT ASSEMBLIES WITH DIRECT TENSION INDICATORS
    PREN 14399-5 : DRAFT 2013 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS
    02/704464 DC : DRAFT MAR 2002 PREN 14399-5 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 5: PLAIN WASHERS FOR SYSTEM HR
    UNI EN 14399-9 : 2009 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES
    UNE-EN 14399-1:2016 High-strength structural bolting assemblies for preloading - Part 1: General requirements
    UNE-EN 14399-6:2016 High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
    BS EN 14399-5 : 2015-02 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS
    BS EN 14399-1:2015 High-strength structural bolting assemblies for preloading General requirements
    I.S. EN 14399-6:2015 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS
    I.S. EN 14399-5:2015 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS
    I.S. EN 14399-1:2015 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS
    DIN 7989-1:2001-04 Washers for steel structures - Part 1: Product grade C
    13/30277437 DC : 0 BS EN 14399-5 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS
    PREN 14399-9 : DRAFT 2015 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES
    PREN 14399-6 : DRAFT 2013 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS
    I.S. EN ISO 7091:2000 PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE C
    DIN EN ISO 7093-1:2000-11 PLAIN WASHERS - LARGE SERIES - PART 1: PRODUCT GRADE A
    DIN EN 14831 E : 2005 FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD
    EN ISO 3269:2000 FASTENERS - ACCEPTANCE INSPECTION
    UNI EN 14831 : 2005 FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD
    I.S. EN ISO 7094:2000 PLAIN WASHERS - EXTRA LARGE SERIES - PRODUCT GRADE C
    DIN 7989-2:2001-04 Washers for steel structures - Part 2: Product grade A
    DIN 440:2001-03 WASHERS - WITH SQUARE HOLE, ESPECIALLY FOR TIMBER CONSTRUCTIONS
    02/704465 DC : DRAFT MAR 2002 PREN 14399-6 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS FOR SYSTEMS HR AND HV
    04/30123693 DC : DRAFT OCT 2004 EN 15048-1 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS
    UNE-EN 14399-5:2016 High-strength structural bolting assemblies for preloading - Part 5: Plain washers
    DIN EN 14399-9:2016-01 (Draft) HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES
    DIN EN ISO 7093-2:2000-11 PLAIN WASHERS - LARGE SERIES - PART 2: PRODUCT GRADE C
    BS EN 14399-6:2005 High-strength structural bolting assemblies for preloading Plain chamfered washers
    BS EN ISO 3269:2001 Fasteners. Acceptance inspection
    BS EN 14831:2005 Fasteners. Tightening performance. Torque/Angle simplified test method
    EN ISO 7089 : 2000 PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE A
    EN 14399-1:2015 High-strength structural bolting assemblies for preloading - Part 1: General requirements
    EN ISO 7093-2 : 2000 PLAIN WASHERS - LARGE SERIES - PART 2: PRODUCT GRADE C
    EN ISO 7091 : 2000 PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE C
    EN 14399-9:2018 High-strength structural bolting assemblies for preloading - Part 9: System HR or HV - Direct tension indicators for bolt and nut assemblies
    EN ISO 7094:2000/AC:2002 PLAIN WASHERS - EXTRA LARGE SERIES - PRODUCT GRADE C
    EN ISO 7090 : 2000 PLAIN WASHERS, CHAMFERED - NORMAL SERIES - PRODUCT GRADE A (ISO 7090:2000)
    EN ISO 7092 : 2000 PLAIN WASHERS - SMALL SERIES - PRODUCT GRADE A
    EN ISO 7093-1 : 2000 PLAIN WASHERS - LARGE SERIES - PART 1: PRODUCT GRADE A (ISO 7093-1:2000)
    EN 14399-5:2015 High-strength structural bolting assemblies for preloading - Part 5: Plain washers
    EN 14831:2005 Fasteners - Tightening performance - Torque/Angle simplified test method
    EN 14399-6:2015 High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
    15/30332554 DC : 0 BS EN 14399-9 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES
    BS EN 14399-9:2009 High strength structural bolting for preloading System HR or HV. Direct tension indicators for bolt and nut assemblies
    I.S. EN 14399-9:2009 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES
    DIN EN 14399-5:2015-04 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS
    DIN EN 14399-1:2015-04 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS
    DIN EN 14399-6:2015-04 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS
    DIN EN 14831:2005-07 Fasteners - Tightening performance - Torque/Angle simplified test method

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
    ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective