EN ISO 6145-1:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Part 1: Methods of calibration (ISO 6145-1:2003)
23-10-2019
20-08-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Calibration methods
4.1 General
4.2 Description of primary or potentially primary
measuring devices
4.3 Measurements on the final mixture
5 Techniques for preparation of gas mixtures calibrated
by the methods described in Clause 4
5.1 General
5.2 Volumetric pumps
5.3 Continuous injection
5.4 Capillary
5.5 Critical orifices
5.6 Thermal mass flow controllers
5.7 Diffusion
5.8 Saturation
5.9 Permeation
Annex A (normative) - Volume measurement by weighing
the water content
Annex B (informative) - Description of secondary devices
which need calibration against primary
devices
Bibliography
ISO 6145-1:2003 specifies the calibration methods involved in the preparation of gas mixtures by dynamic volumetric techniques. It also gives a brief presentation of a non-exhaustive list of examples of dynamic volumetric techniques which are described in more detail in other parts of ISO 6145.
| Committee |
CEN/BT
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN ISO 6145-1:2008 | Identical |
| ONORM EN ISO 6145-1 : 2008 | Identical |
| ISO 6145-1:2003 | Identical |
| NF EN ISO 6145-1 : 2008 | Identical |
| NS EN ISO 6145-1 : 1ED 2008 | Identical |
| SS-EN ISO 6145-1:2008 | Identical |
| SS-EN ISO 6145-1:2018 | Identical |
| DIN EN ISO 6145-1:2008-11 | Identical |
| NEN EN ISO 6145-1 : 2008 | Identical |
| NBN EN ISO 6145-1 : 2009 | Identical |
| SN EN ISO 6145-1:2020 | Identical |
| UNI EN ISO 6145-1 : 2009 | Identical |
| I.S. EN ISO 6145-1:2008 | Identical |
| PN EN ISO 6145-1 : 2011 | Identical |
| BS EN ISO 6145-1:2008 | Identical |
| SN EN ISO 6145-1 : 2008 | Identical |
| I.S. EN 838:2010 | WORKPLACE EXPOSURE - PROCEDURES FOR MEASURING GASES AND VAPOURS USING DIFFUSIVE SAMPLERS - REQUIREMENTS AND TEST METHODS |
| EN 1076:2009 | Workplace exposure - Procedures for measuring gases and vapours using pumped samplers - Requirements and test methods |
| UNE-EN 60079-29-1:2017 | Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases |
| DIN EN 1076:2010-04 | Workplace exposure - Procedures for measuring gases and vapours using pumped samplers - Requirements and test methods |
| VDI 2100 Blatt 3:2011-10 | Determination of gaseous compounds in ambient air - Determination of indoor air pollutants - Gas chromatographic determination of organic compounds - Active sampling by accumulation on adsorbents - Thermal desorption |
| BS EN 60079-29-1:2007 | Explosive atmospheres Gas detectors. Performance requirements of detectors for flammable gases |
| BS EN 1076:2009 | Workplace exposure. Procedures for measuring gases and vapours using pumped samplers. Requirements and test methods |
| UNI EN 1076 : 2010 | WORKPLACE EXPOSURE - PROCEDURES FOR MEASURING GASES AND VAPOURS USING PUMPED SAMPLERS - REQUIREMENTS AND TEST METHODS |
| UNI EN 838 : 2010 | WORKPLACE EXPOSURE - PROCEDURES FOR MEASURING GASES AND VAPOURS USING DIFFUSIVE SAMPLERS - REQUIREMENTS AND TEST METHODS |
| DIN EN 838:2010-05 | Workplace exposure - Procedures for measuring gases and vapours using diffusive samplers - Requirements and test methods |
| BS EN 838:2010 | Workplace exposure. Procedures for measuring gases and vapours using diffusive samplers. Requirements and test methods |
| I.S. EN 1076:2009 | WORKPLACE EXPOSURE - PROCEDURES FOR MEASURING GASES AND VAPOURS USING PUMPED SAMPLERS - REQUIREMENTS AND TEST METHODS |
| EN 838:2010 | Workplace exposure - Procedures for measuring gases and vapours using diffusive samplers - Requirements and test methods |
| ISO/IEC Guide 98:1993 | Guide to the expression of uncertainty in measurement (GUM) |
| ISO 6145-7:2009 | Gas analysis Preparation of calibration gas mixtures using dynamic volumetric methods Part 7: Thermal mass-flow controllers |
| ISO/IEC Guide 99:2007 | International vocabulary of metrology Basic and general concepts and associated terms (VIM) |
| ISO 6143:2001 | Gas analysis — Comparison methods for determining and checking the composition of calibration gas mixtures |
| ISO 6142:2001 | Gas analysis Preparation of calibration gas mixtures Gravimetric method |
| ISO 6145-10:2002 | Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 10: Permeation method |
| ISO 6145-2:2014 | Gas analysis — Preparation of calibration gas mixtures using dynamic methods — Part 2: Piston pumps |
| ISO 6145-5:2009 | Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 5: Capillary calibration devices |
| ISO 6145-4:2004 | Gas analysis Preparation of calibration gas mixtures using dynamic volumetric methods Part 4: Continuous syringe injection method |
| ISO 7504:2015 | Gas analysis Vocabulary |
| ISO 6145-9:2009 | Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 9: Saturation method |
| ISO 6145-6:2017 | Gas analysis — Preparation of calibration gas mixtures using dynamic methods — Part 6: Critical flow orifices |
| ISO 6145-8:2005 | Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 8: Diffusion method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.