Skip to content
Please enter a keyword to search

  • EN ISO 62:2008

    Current The latest, up-to-date edition.

    Plastics - Determination of water absorption (ISO 62:2008)

    Available format(s): 

    Language(s): 

    Published date:  15-02-2008

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Principle
    4 Apparatus
    5 Test specimens
      5.1 General
      5.2 Square-shaped test specimens for homogeneous
          plastics
      5.3 Test specimens of reinforced plastics affected by
          anisotropic diffusion effects
      5.4 Tubular test specimens
      5.5 Rod-shaped test specimens
      5.6 Specimens cut from finished products, extrusion
          compounds, sheets or laminates
    6 Test conditions and procedures
      6.1 General
      6.2 General conditions
      6.3 Method 1: Determination of amount of water absorbed
          after immersion in water at 23 degrees C
      6.4 Method 2: Determination of amount of water absorbed
          after immersion in boiling water
      6.5 Method 3: Determination of water-soluble matter lost
          during immersion
      6.6 Method 4: Determination of amount of water absorbed after
          exposure to 50% relative humidity
    7 Expression of results
      7.1 Percentage by mass of water absorbed
      7.2 Determination of the water content at saturation and the
          water diffusion coefficient using Fick's laws
    8 Precision
    9 Test report
    Annex A (informative) - Correlation between water absorption by
            test specimens and Fick's diffusion laws
    Annex B (informative) - Precision statement
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 62:2008 describes a procedure for determining the moisture absorption properties in the “through-the-thickness” direction of flat or curved-form solid plastics. It also describes procedures for determining the amount of water absorbed by plastic specimens of defined dimensions, when immersed in water or when subjected to humid air under controlled conditions. The “through-the-thickness” moisture diffusion coefficient can be determined for single-phase material by assuming Fickian diffusion behaviour with constant moisture absorption properties through the thickness of the test specimen. This model is valid for homogeneous materials and for reinforced polymer-matrix composites tested below their glass transition temperature. However, some two-phase matrices such as hardened epoxies may require a multi-phase absorption model which is not covered by this International Standard.The results obtained using the methods described in this International Standard are applicable to most plastics but are not applicable to cellular plastics, granulates or powders, which can show additional absorption and capillary effects. Plastics exposed to moisture under controlled conditions for defined periods of time provide relative comparisons between them.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 249
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    12/30265310 DC : 0 BS EN 124-5 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE FROM COMPOSITE MATERIALS
    14/30303794 DC : 0 BS EN 438-2 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES
    PREN 438-2 : DRAFT 2014 HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES
    BS EN 4702-05:2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 05: RETAINING WASHER
    UNI EN 15836-2 : 2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM
    CEI 20-95 : 2010 ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS
    PREN 13160-7 : DRAFT 2014 LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
    PREN 4702-05 : DRAFT 2016 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 05: RETAINING WASHER
    BS EN ISO 12215-1:2000 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 1: MATERIALS: THERMOSETTING RESINS, GLASS-FIBRE REINFORCEMENT, REFERENCE LAMINATE
    I.S. EN 15836-2:2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM
    I.S. EN 50290-2-35:2016 COMMUNICATION CABLES - PART 2-35: COMMON DESIGN RULES AND CONSTRUCTION - POLYAMIDE SHEATHING COMPOUND
    I.S. HD 631.2:2007 ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS
    HD 631.2 : 2007 ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS
    DD CEN/TS 14632:2006 PLASTICS PIPING SYSTEMS FOR DRAINAGE, SEWERAGE AND WATER SUPPLY, PRESSURE AND NON-PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    ISO 7823-2:2003 Plastics Poly(methyl methacrylate) sheets Types, dimensions and characteristics Part 2: Extruded sheets
    EN ISO 899-2:2003/A1:2015 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading - Amendment 1 (ISO 899-2:2003/Amd 1:2015)
    DIN EN 14598-2:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements
    BS EN 14620-4:2006 Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0°C and -165°C Insulation components
    BS EN ISO 1622-2:1999 PLASTICS - POLYSTYRENE (PS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN 13677-2:2003 Reinforced thermoplastic moulding compounds. Specification for GMT Methods of test and general requirements
    UNE-EN 16245-2:2014 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers
    BS EN 61241-18:2004 ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 18: PROTECTION BY ENCAPSULATION "MD"
    BS EN 60893-2:2004 Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Methods of test
    BS EN ISO 2580-2:2003 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    I.S. EN ISO 7823-1:2003 PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: CAST SHEETS
    EN 10310:2003 Steel tubes and fittings for onshore and offshore pipelines - Internal and external polyamide powder based coatings
    EN 60684-2:2011 Flexible insulating sleeving - Part 2: Methods of test
    EN 124-5:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials
    EN 13160-7:2016 Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets
    EN 60893-2:2004 Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test
    DIN EN 15189:2007-02 Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods
    EN 61212-2:2006 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test
    DIN EN 15836-1:2010-11 Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 1: Homogenous membranes of nominal thickness equal to or greater than 0,75 mm
    UNE-EN 15836-1:2010 Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 1: Homogenous membranes of nominal thickness equal to or greater than 0,75 mm
    11/30239977 DC : 0 BS EN 16245-2 - FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: ADDITIONAL REQUIREMENTS FOR RESINS, CURING SYSTEMS, ADDITIVES AND MODIFIERS
    DIN EN 16245-2:2013-08 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers
    CEI EN 50290-2-35 : 1ED 2017 COMMUNICATION CABLES - PART 2-35: COMMON DESIGN RULES AND CONSTRUCTION - POLYAMIDE SHEATHING COMPOUND
    EN IEC 62677-2:2018 Heat shrinkable low and medium voltage moulded shapes - Part 2 Methods of test
    EN 4702-05:2017 Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer
    14/30301266 DC : 0 BS EN 13160-7 - LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
    BS ISO 7391-2 : 1996 AMD 10746 PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    08/30181781 DC : DRAFT JULY 2008 BS EN 15836-2 - PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM
    08/30181778 DC : DRAFT JULY 2008 BS EN 15836-1 - PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM
    I.S. EN 4702-05:2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 05: RETAINING WASHER
    I.S. EN IEC 62677-2:2018 HEAT SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 2: METHODS OF TEST
    I.S. EN 60212:2011 STANDARD CONDITIONS FOR USE PRIOR TO AND DURING THE TESTING OF SOLID ELECTRICAL INSULATING MATERIALS
    DIN EN ISO 2580-2:2004-05 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN ISO 15526-2:2004 PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN 438-2 : 2016 HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES
    BS EN 14598-2:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements
    I.S. EN ISO 15526-2:2004 PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    I.S. EN 13160-7:2016 LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
    I.S. EN 61212-2:2006 INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
    I.S. EN 60893-2:2004 INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
    I.S. EN ISO 4894-2:1999 PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    DIN EN ISO 15526-2:2004-10 PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    I.S. EN ISO 899-2:2003 PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 2: FLEXURAL CREEP BY THREE-POINT LOADING (ISO 899-2:2003)
    VDI 3822 Blatt 2.1.8:2012-01 FAILURE ANALYSIS - DEFECTS OF THERMOPLASTIC PRODUCTS MADE OF PLASTICS CAUSED BY WEATHER-INDUCED STRESS
    BS EN 50617-1:2015 Railway applications. Technical parameters of train detection systems for the interoperability of the trans-European railway system Track circuits
    BS EN 4702-03:2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
    UNE-EN 15836-2:2010 Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 2: Reinforced membranes of nominal thickness equal to or greater than 1,5 mm
    UNE-EN 124-5:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials
    03/105151 DC : DRAFT MAR 2003 PREN 14620-4 - DESIGN AND MANUFACTURE OF SITE BUILT, VERTICAL, CYLINDRICAL, FLAT-BOTTOMED STEEL TANKS FOR THE STORAGE OF REFRIGERATED, LIQUEFIED GASES WITH OPERATING TEMPERATURES BETWEEN -5 DEGREES C AND -165 DEGREES C - PART 4: INSULATION COMPONENTS
    02/121747 DC : DRAFT APR 2002 PREN 438-2 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES
    07/30166095 DC : 0 EN 124 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS
    BS EN 60684-2:2011 Flexible insulating sleeving Methods of test
    EN 4702-03 : 2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
    UNE-EN 438-2:2016 High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 2: Determination of properties
    PREN 4702-03 : DRAFT 2016 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
    EN 438-2:2016 High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties
    I.S. EN 60455-2:2015 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 2: METHODS OF TEST
    I.S. EN 438-2:2016 HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES
    I.S. EN 16245-2:2013 FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS
    I.S. EN 124-5:2015 GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE OF COMPOSITE MATERIALS
    I.S. EN 15836-1:2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM
    NF EN 15836-2 : 2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM
    UNE-EN 13160-7:2017 Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets
    EN 61760-4:2015/A1:2018 SURFACE MOUNTING TECHNOLOGY - PART 4: CLASSIFICATION, PACKAGING, LABELLING AND HANDLING OF MOISTURE SENSITIVE DEVICES (IEC 61760-4:2015/A1:2018)
    DIN EN ISO 2897-2:2004-05 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN 10310:2003 STEEL TUBES FOR FITTINGS FOR ONSHORE AND OFFSHORE PIPELINES - INTERNAL AND EXTERNAL POLYAMIDE POWDER BASED COATINGS
    EN 16245-2:2013 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers
    UNI EN 16245-2 : 2013 FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS
    UNI EN 15189 : 2007 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
    DIN EN 15836-2:2010-11 Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 2: Reinforced membranes of nominal thickness equal to or greater than 1,5 mm
    UNI EN 15836-1 : 2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM
    BS EN 124-5:2015 Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of composite materials
    BS EN 15836-1:2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0.75 MM
    I.S. EN 60684-2:2011 FLEXIBLE INSULATING SLEEVING - PART 2: METHODS OF TEST (IEC 60684-2:2011)
    DIN EN 124-5 E : 2015 GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE OF COMPOSITE MATERIALS
    BS EN 16245-2:2013 Fibre-reinforced plastic composites. Declaration of raw material characteristics Specific requirements for resin, curing systems, additives and modifiers
    UNE-EN 50617-1:2015 Railway applications - Technical parameters of train detection systems for the interoperability of the trans-European railway system - Part 1: Track circuits
    UNE-EN 10310:2011 Steel tubes and fittings for onshore and offshore pipelines - Internal and external polyamide powder based coatings
    BS EN 60455-2:2015 Resin based reactive compounds used for electrical insulation Methods of test
    BS 7933-2:2007 ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS
    16/30336750 DC : 0 BS EN 50290-2-35 - COMMUNICATION CABLES - PART 2-35: COMMON DESIGN RULES AND CONSTRUCTION - POLYAMIDE SHEATHING COMPOUND
    DIN EN 124-5:2015-09 GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE OF COMPOSITE MATERIALS
    I.S. EN 50617-1:2015 RAILWAY APPLICATIONS - TECHNICAL PARAMETERS OF TRAIN DETECTION SYSTEMS FOR THE INTEROPERABILITY OF THE TRANS-EUROPEAN RAILWAY SYSTEM - PART 1: TRACK CIRCUITS
    DIN EN 438-2:2016-06 HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES
    02/124520 DC : DRAFT DEC 2002 EN 14598-3 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS
    DIN EN 15189 E : 2007 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
    BS EN 13677-3:2003 Reinforced thermoplastic moulding compounds. Specification for GMT Specific requirements
    BS EN 13160-7:2003 Leak detection systems General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jackets
    BS EN ISO 3672-2:2001 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN ISO 899-2 : 2003 PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 2: FLEXURAL CREEP BY THREE-POINT LOADING
    DIN EN 15334 E : 2007 SANITARY APPLIANCES - METHACRYLIC DISPERSIONS OF HIGH FILLER CONTENT
    BS EN ISO 10366-2:2003 PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    ISO 2580-2:2003 Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    BS EN ISO 7823-2:2003 Plastics. Poly(methyl methacrylate) sheets. Types, dimensions and characteristics Extruded sheets
    ISO 4894-2:1995 Plastics Styrene/acrylonitrile (SAN) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 3672-2:2000 Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and determination of properties
    ISO 7823-1:2003 Plastics Poly(methyl methacrylate) sheets Types, dimensions and characteristics Part 1: Cast sheets
    BS EN 15189:2006 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
    BS EN ISO 7823-1:2003 PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: CAST SHEETS
    ISO 6402-2:2003 Plastics Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 10366-2:2003 Plastics Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    BS EN ISO 6402-2:2003 PLASTICS - ACRYLONITRILE-STYRENE-ACRYLATE (ASA), ACRYLONITRILE-(ETHYLENE-PROPYLENE-DIENE)-STYRENE (AEPDS) AND ACRYLONITRILE-(CHLORINATED POLYETHYLENE)-STYRENE (ACS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    DIN EN 15334:2007-05 Sanitary appliances - Methacrylic dispersions of high filler content
    ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
    EN 61241-18:2004 Electrical apparatus for use in the presence of combustible dust - Part 18: Protection by encapsulation "mD"
    EN 15334:2007 Sanitary appliances - Methacrylic dispersions of high filler content
    EN ISO 15252-2 : 1999 PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 15189:2006 Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods
    EN 14598-2:2005/AC:2006 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
    EN 13677-3:2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3: Specific requirements
    EN 13677-2:2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 2: Methods of test and general requirements
    EN ISO 14529-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 15526-2:2004 Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15526-2:2000)
    EN ISO 10366-2 : 2003 PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 3672-2 : 2001 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 2580-2 : 2003 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 14530-2 : 1999 PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 14528-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 7823-1:2003 Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 1: Cast sheets (ISO 7823-1:2003)
    EN ISO 4894-2 : 1999 PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 15836-2:2010 Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 2: Reinforced membranes of nominal thickness equal to or greater than 1,5 mm
    EN ISO 7823-2 : 2003 PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 2: EXTRUDED SHEETS
    EN 14620-4:2006 Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 4: Insulation components
    EN 15836-1:2010 Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 1: Homogenous membranes of nominal thickness equal to or greater than 0,75 mm
    EN ISO 6402-2 : 2003 PLASTICS - ACRYLONITRILE-STYRENE-ACRYLATE (ASA), ACRYLONITRILE-(ETHYLENE-PROPYLENE-DIENE)-STYRENE (AEPDS) AND ACRYLONITRILE-(CHLORINATED POLYETHYLENE)-STYRENE (ACS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 14527-2 : 1999 PLASTICS - UREA-FORMALDEHYDE AND UREA/MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (UF- AND UF/MF-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    I.S. EN 4702-03:2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
    BS EN 60212:2011 Standard conditions for use prior to and during the testing of solid electrical insulating materials
    I.S. CEN TS 14632:2006 PLASTICS PIPING SYSTEMS FOR DRAINAGE, SEWERAGE AND WATER SUPPLY, PRESSURE AND NON-PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    PREN 50290-2-35 : DRAFT 2016 COMMUNICATION CABLES - PART 2-35: COMMON DESIGN RULES AND CONSTRUCTION - POLYAMIDE SHEATHING COMPOUND
    CEI EN 60893-2 : 2005 INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
    CEI EN 60684-2 : 2012 FLEXIBLE INSULATING SLEEVING - PART 2: METHODS OF TEST
    BS EN 15836-2:2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM
    CEI EN 60212 : 2012 STANDARD CONDITIONS FOR USE PRIOR TO AND DURING THE TESTING OF SOLID ELECTRICAL INSULATING MATERIALS
    04/30055611 DC : 0 BS EN 124 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS
    BS EN 61760-4 : 2015 SURFACE MOUNTING TECHNOLOGY - PART 4: CLASSIFICATION, PACKAGING, LABELLING AND HANDLING OF MOISTURE SENSITIVE DEVICES
    UNE-EN 50290-2-35:2016 Communication cables - Part 2-35: Common design rules and construction - Polyamide sheathing compound
    NF EN 15836-1 : 2010 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM
    I.S. EN 61760-4:2015 SURFACE MOUNTING TECHNOLOGY - PART 4: CLASSIFICATION, PACKAGING, LABELLING AND HANDLING OF MOISTURE SENSITIVE DEVICES
    DIN EN ISO 2580-2 E : 2004 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN ISO 1163-2:2000 PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE)(PVC-U) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN 15334:2007 Sanitary appliances. Methacrylic dispersions of high filler content
    ISO 15526-2:2000 Plastics Polyketone (PK) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    02/124519 DC : DRAFT DEC 2002 EN 14598-2 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
    BS EN 61212-2:2006 Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Methods of test
    DIN EN 10310:2004-07 Steel tubes and fittings for onshore and offshore pipelines - Internal and external polyamide powder based coatings
    EN 60212:2011 Standard conditions for use prior to and during the testing of solid electrical insulating materials
    EN 60455-2:2015 Resin based reactive compounds used for electrical insulation - Part 2: Methods of test
    EN 50290-2-35 : 2016 Communication cables - Part 2-35: Common design rules and construction - Polyamide sheathing compound
    EN 50617-1:2015 Railway applications - Technical parameters of train detection systems for the interoperability of the trans-European railway system - Part 1: Track circuits

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
    ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective