ETS 300 162 : 20002

Foreword
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
  3.1 Definitions
  3.2 Symbols
  3.3 Abbreviations
4 General and operational requirements
  4.1 Construction
  4.2 Controls and indicators
  4.3 Handset and loudspeaker
  4.4 Safety precautions
  4.5 Labelling
  4.6 Warm up
5 Technical requirements
  5.1 Switching time
  5.2 Class of emission and modulation characteristics
  5.3 Multiple watch facilities
  5.4 DSC controller interfaces
6 General conditions of measurement
  6.1 Arrangements for test signals applied to the
      receiver input
  6.2 Squelch
  6.3 Normal test modulation
  6.4 Artificial antenna
  6.5 Arrangements for test signals applied to the
      transmitter input
  6.6 Test channels
  6.7 Measurement uncertainty and interpretation of the
      measured results
  6.8 Test conditions, power sources and ambient
      temperatures
  6.9 Normal test conditions
  6.10 Extreme test conditions
  6.11 Procedure for tests at extreme temperatures
7 Environmental tests
  7.1 Procedure
  7.2 Performance check
  7.3 Vibration test
  7.4 Temperature tests
8 Transmitter
  8.1 Frequency error
  8.2 Carrier power
  8.3 Frequency deviation
  8.4 Sensitivity of the modulator, including
      microphone
  8.5 Audio frequency response
  8.6 Audio frequency harmonic distortion of the
      emission
  8.7 Adjacent channel power
  8.8 Conducted spurious emissions conveyed to the
      antenna
  8.9 Cabinet radiation and conducted spurious
      emissions other than those conveyed to the
      antenna
  8.10 Residual modulation of the transmitter
  8.11 DSC audio input characteristics
  8.12 DSC audio input limitation
  8.13 Modulation attack time
  8.14 Transient frequency behaviour of the
       transmitter
9 Receiver
  9.1 Harmonic distortion and rated audio frequency
      output power
  9.2 Audio frequency response
  9.3 Maximum usable sensitivity
  9.4 Co-channel rejection
  9.5 Adjacent channel selectivity
  9.6 Spurious response rejection
  9.7 Intermodulation response
  9.8 Blocking or desensitization
  9.9 Conducted spurious emissions
  9.10 Radiated spurious emissions
  9.11 Receiver noise and hum level
  9.12 Squelch operation
  9.13 Squelch hysteresis
  9.14 Multiple watch characteristic
  9.15 DSC audio output characteristic
10 Duplex operation
  10.1 Receiver desensitization with simultaneous
       transmission and reception
  10.2 Duplex transceiver internal mixing
Annex A (normative): Measuring receiver for adjacent
                     channel power measurement
  A.1 Power measuring receiver specification
Annex B (normative): Subclauses of this ETS relevant
                     for compliance with the essential
                     requirements of relevant EC
                     Council Directives
Annex C (normative): Protocol for the IEC 1162-1 [9]
                     commands Frequency Set
                     Information (FSI)
  C.1 Frequency Set Information (FSI)
Annex D (normative): ERC Decision on the adoption of
                     approval regulations for
                     radiotelephone transmitters and
                     receivers for the maritime mobile
                     service operating in the frequency
                     range 156 MHz to 174 MHz, based on
                     European Telecommunications
                     Standard (ETS) 300 162
Annex E (normative): Radiated measurements
  E.1 Test sites and general arrangements for
      measurements involving the use of radiated fields
  E.2 Guidance on the use of radiation test sites
  E.3 Further optional alternative indoor test site
      using an anechoic chamber
History

Revision of ETS 300 162 to bring it into line with ETR 238 and to form part of a harmonised standard under the EMC Directive together with ETS 300 828.