ETS 300 176-1 : 20002

Foreword
1 Scope
2 Normative references
3 Definitions and abbreviations
   3.1 Definitions
   3.2 Abbreviations
4 General
   4.1 Document layout
   4.2 Presentation of equipment for testing purposes
   4.3 Applicability of type tests
   4.4 Interpretation of the measurement results
5 General test requirements
   5.1 Test philosophy
   5.2 Test site
   5.3 Standard position
   5.4 Test antenna of the LT
   5.5 Substitution antenna
   5.6 Test fixture
   5.7 Indoor test site
   5.8 Lower Tester (LT)
   5.9 Upper Tester (UT)
   5.10 Description of the lower tester FT and PT
   5.11 General test methods
   5.12 Test setup
   5.13 Test arrangements for intermodulation
        measurements
6 Test conditions, power sources and ambient
   temperatures
   6.1 General
   6.2 Nominal test conditions
   6.3 Extreme test conditions
   6.4 Test power source - general requirements
   6.5 Nominal test power source
   6.6 Extreme test power source
   6.7 Testing of host connected equipment and
       plug-in cards
7 Accuracy and stability of RF carriers
   7.1 Definition
   7.2 Test environment
   7.3 Method of measurement
   7.4 Verdict criteria when the EUT is a RFP
   7.5 Verdict criteria when the EUT is a PP
8 Accuracy and stability of timing parameters
   8.1 Slot structure definitions
   8.2 Definition of the position of p0
   8.3 Measurement of packet timing jitter
   8.4 Measurement of the reference timing accuracy
       of a RFP
   8.5 Measurement of packet transmission accuracy
       of a PP
9 Transmission burst
   9.1 Definitions
   9.2 Test environment
   9.3 Method of measurement
   9.4 Verdict criteria
10 Transmitted power
   10.1 Definitions
   10.2 PP and RFP with an integral antenna
   10.3 PP and RFP with external antenna connection(s)
11 RF carrier modulation
   11.1 Test environment
   11.2 Method of measurement, Parts 1 and 2
   11.3 Method of measurement, Parts 3 and 4
   11.4 Verdict criteria for Part 1
   11.5 Verdict criteria for Part 2
   11.6 Verdict criteria for Part 3
   11.7 Verdict criteria for Part 4
12 Unwanted RF power radiation
   12.1 General test conditions
   12.2 Emissions due to modulation
   12.3 Emissions due to transmitter transients
   12.4 Emissions due to intermodulation
   12.5 Spurious emissions when allocated a transmit
        channel
13 Radio receiver testing
14 Synchronization port (FP only)
15 EMC
16 Equipment identity testing
17 Efficient use of the radio spectrum
Annex A (informative): Bibliography
Annex B (normative): Procedures for test fixture
        calibration and for measurement of radiated
        spurious emissions
Annex C (normative): Procedure for measurement of
        conducted spurious emissions
Annex D (normative): Test Support Profile (TSP)
Annex E (normative): Measurement of BER
Annex F (informative): Procedures for the measurement
        of synchronization loss at the EUT by the LT
Annex G (normative): Requirements for PPs with direct
        PP to PP communication mode
Annex H (normative): Requirements for installation
        related issues
Annex I (informative): Essential requirements
        justification
Annex J (normative): Additions to ETS 300 175-2
History

Specifies the approval tests applicable to all Digital Enhanced Cordless Telecommunications (DECT) equipment accessing the DECT frequency band 1 880 MHz to 1 900 MHz and the approval tests applicable to DECT speech transmission using CCITT Recommendation G.726 [14] ADPCM speech codec at 32 kbit/ss.