Skip to content
Please enter a keyword to search
  • Preview

    I.S. CEN ISO TS 15011-5:2006

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 5: IDENTIFICATION OF THERMAL-DEGRADATION PRODUCTS GENERATED WHEN WELDING OR CUTTING THROUGH PRODUCTS COMPOSED WHOLLY OR PARTLY OF ORGANIC MATERIALS

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-10-2011

    Language(s):  English

    Published date:  01-01-2006

    Publisher:  National Standards Authority of Ireland

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Procedure
      5.1 Screening tests to identify thermal degradation
          products
      5.2 Production of safety data sheet information
      5.3 Production of user-specific risk assessment data
      5.4 Data handling
    6 Use and comprehensiveness of data on thermal degradation
      products
      6.1 Use of data on thermal degradation products
      6.2 Comprehensiveness of data on thermal degradation
          products
    7 Test report
    Annex A (normative) Screening tests to identify thermal
                          degradation products
    Annex B (normative) Procedures for determination of thermal
                          degradation products
    Annex C (informative) Sampling chambers
    Annex D (normative) Sampling and analytical procedures
    Annex E (informative) Example of a test report sheet
    Annex F (informative) Examples of suitable test conditions for
                          arc welding
    Annex G (informative) Use of data on thermal degradation products
    Bibliography

    Abstract - (Show below) - (Hide below)

    Specifies procedures for obtaining information about thermal degradation products generated when welding, cutting through, preheating and straightening products composed wholly or partly of organic substances, e.g. shop primers, paints, adhesives, waxes, sealants, pressing lubricant, oils, etc.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 14373:2015 Resistance welding — Procedure for spot welding of uncoated and coated low carbon steels
    ISO 17734-1:2013 Determination of organonitrogen compounds in air using liquid chromatography and mass spectrometry — Part 1: Isocyanates using dibutylamine derivatives
    ISO 16017-1:2000 Indoor, ambient and workplace air — Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography — Part 1: Pumped sampling
    ISO 16702:2007 Workplace air quality — Determination of total organic isocyanate groups in air using 1-(2-methoxyphenyl)piperazine and liquid chromatography
    ISO 17734-2:2013 Determination of organonitrogen compounds in air using liquid chromatography and mass spectrometry — Part 2: Amines and aminoisocyanates using dibutylamine and ethyl chloroformate derivatives
    ISO 14327:2004 Resistance welding Procedures for determining the weldability lobe for resistance spot, projection and seam welding
    ISO 16000-3:2011 Indoor air — Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air — Active sampling method
    ISO 15011-2:2009 Health and safety in welding and allied processes Laboratory method for sampling fume and gases Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging
    ISO 15011-1:2009 Health and safety in welding and allied processes — Laboratory method for sampling fume and gases — Part 1: Determination of fume emission rate during arc welding and collection of fume for analysis
    ISO 16000-6:2011 Indoor air Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TA sorbent, thermal desorption and gas chromatography using MS or MS-FID
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective