Skip to content
Please enter a keyword to search
  • Preview

    I.S. CEN TS 14807:2004

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE STRUCTURAL ANALYSIS OF BURIED GRP-UP PIPELINES

    Available format(s):  Hardcopy, PDF

    Superseded date:  21-12-2013

    Language(s):  English

    Published date:  01-01-2004

    Publisher:  National Standards Authority of Ireland

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Requirements
    5 Classification and designation
    Bibliography

    Abstract - (Show below) - (Hide below)

    Specifies limits applicable to glass-reinforced thermosetting plastics (GRP) pipes used for the conveyance of liquids under pressure or gravity conditions.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1227 : 1997 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES - DETERMINATION OF THE LONG-TERM ULTIMATE RELATIVE RING DEFLECTION UNDER WET CONDITIONS
    EN 1295-1:1997 Structural design of buried pipelines under various conditions of loading - Part 1: General requirements
    ISO/TR 10465-2:2007 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 2: Comparison of static calculation methods
    EN 805:2000 Water supply - Requirements for systems and components outside buildings
    ISO/TR 10465-3:2007 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 3: Installation parameters and application limits
    PREN 14364 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
    EN 1120:1996 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition
    ISO 14828:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor
    EN 1447:2009+A1:2010 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
    ISO/TR 10465-1:1993 Underground installation of flexible glass-reinforced thermosetting resin (GRP) pipes Part 1: Installation procedures
    EN 1226:1996 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection
    ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
    PREN 1796 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
    ISO 10471:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
    EN 1228:1996 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness
    EN 1610:2015 Construction and testing of drains and sewers
    EN 705:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES AND FITTINGS - METHODS FOR REGRESSION ANALYSES AND THEIR USE
    CEN/TS 14578:2013 Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation
    ENV 1046:2001 Plastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for installation above and below ground
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective