I.S. EN 10002-5:1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
METALLIC MATERIALS - TENSILE TESTING - PART 5: METHOD OF TESTING AT ELEVATED TEMPERATURE
Hardcopy , PDF
23-02-2011
English
01-01-1992
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1 Scope
2 Normative references
3 PRINCIPLE
4 DEFINITIONS
4.1 Gauge length (L)
4.2 Parallel length (L[c])
4.3 Elongation
4.4 Percentage elongation
4.5 Extensometer gauge length (L[e])
4.6 Extension
4.7 Percentage reduction of area (Z)
4.8 Maximum force (F[m])
4.9 Stress
5 SYMBOLS AND DESIGNATIONS
6 TEST PIECES
6.1 Shape and dimensions
6.2 Types
6.3 Preparation of test pieces
7 DETERMINATION OF ORIGINAL CROSS-SECTIONAL AREA (S[O])
8 MARKING THE ORIGINAL GAUGE LENGTH (L[O])
9 TESTING APPARATUS
9.1 Testing machine
9.2 Extensometer
9.3 Heating device
10 CONDITIONS OF TESTING
10.1 Heating of the test piece
10.2 Loading of the test piece
10.3 Rate of loading
10.4 Method of gripping
11 DETERMINATION OF PERCENTAGE ELONGATION AFTER FRACTURE (A)
12 DETERMINATION OF PROOF STRENGTH (NON-PROPORTIONAL EXTENSION)
(R[p])
13 DETERMINATION OF PROOF STRENGTH (TOTAL EXTENSION) (R[t])
14 METHOD OF VERIFICATION OF PERMANENT SET STRENGTH (R[r])
15 TEST REPORT
Annex A (Normative annex) TYPES OF TEST PIECE TO BE USED FOR THIN
PRODUCTS: SHEETS, STRIPS AND FLATS BETWEEN 0.1 mm AND 3 mm
Annex B (Normative annex) TYPES OF TEST PIECES TO BE USED IN THE CASE
OF WIRE, BARS AND SECTIONS WITH A DIAMETER OR THICKNESS OF LESS
THAN 4 mm
Annex C (Normative annex) TYPES OF TEST PIECES TO BE USED IN THE CASE
OF SHEETS AND FLATS OF THICKNESS EQUAL TO OR GREATER THAN 3 mm,
AND WIRE, BARS AND SECTIONS OF DIAMETER OR THICKNESS EQUAL TO
OR GREATER THAN 4 mm
Annex D (Normative annex) TYPES OF TEST PIECES TO BE USED IN THE CASE
OF TUBES
Annex E (Normative annex) MEASUREMENT OR PERCENTAGE ELONGATION AFTER
FRACTURE, BASED ON SUB-DIVISION OF THE ORIGINAL GAUGE LENGTH
Annex F (Informative annex) LIST OF NATIONAL STANDARDS CORRESPONDING
TO REFERENCE EURONORM 18
Annex G (Informative annex) Bibliography
Describes the method for tensile testing of metallic materials and defines the mechanical properties which can be determined thereby at elevated temperature.
| DocumentType |
Standard
|
| Pages |
39
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| BS EN 10002-5:1992 | Identical |
| NBN EN 10002-5 : 1992 | Identical |
| NEN EN 10002-5 : 1992 | Identical |
| UNI EN 10002-5 : 1993 | Identical |
| DIN EN 10002-5:1992-02 | Identical |
| NS EN 10002-5 : 1ED 1992 | Identical |
| NF EN 10002-5 : 1992 | Identical |
| EN 10002-5:1991 | Identical |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10002-2 : 1991 | METALLIC MATERIALS - TENSILE TESTING - PART 2: VERIFICATION OF THE FORCE MEASURING SYSTEM OF THE TENSILE TESTING MACHINE |
| ISO 2566-2:1984 | Steel Conversion of elongation values Part 2: Austenitic steels |
| EN 18 : LATEST | |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| EN 10002-4 : 1994 | METALLIC MATERIALS - TENSILE TEST - VERIFICATION OF EXTENSOMETERS USED IN UNIAXIAL TESTING |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.