![header thumbnail](/images/publishers\nsai_cover.gif)
I.S. EN 12245:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\nsai_cover.gif)
TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS
27-04-2022
27-02-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Design and manufacture
5 Cylinder and material tests
6 Conformity evaluation
7 Marking
8 Operating instructions (cylinders with non-metallic
liners)
Annex A (normative) - Prototype, design variant and
production testing
Annex B (informative) - Examples of prototype approval
and production testing certificates
Bibliography
Defines minimum requirements for the materials, design, construction, prototype testing and routine manufacturing inspections of composite gas cylinders for compressed, liquefied and dissolved gases.
DevelopmentNote |
2009 Edition Re-Issued in November 2011 & incorporates AMD 1 2011. (11/2011)
|
DocumentType |
Standard
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
ONORM EN 12245 : 2012 | Identical |
UNE-EN 12245:2009 | Identical |
DIN EN 12245:2012-03 | Identical |
NF EN 12245 : 2009 + A1 2012 | Identical |
UNI EN 12245 : 2011 | Identical |
NS EN 12245 : 2009 + A1 2011 | Identical |
EN 12245:2009+A1:2011 | Identical |
SN EN 12245+A1:2012 | Identical |
NEN EN 12245 : 2009 + A1 2011 | Identical |
NBN EN 12245 : 2009 + A1 2011 | Identical |
ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
ISO 8521:2009 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength |
ASTM D 3418 : 2015 : REDLINE | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
EN 629-2 : 1996 | TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - GAUGE INSPECTION |
CGA C 14 : 2005(R2010) | PROCEDURES FOR FIRE TESTING OF DOT CYLINDER PRESSURE RELIEF DEVICE SYSTEMS |
ISO 11114-1:2012 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials |
EN ISO 11120:2015 | Gas cylinders - Refillable seamless steel tubes of water capacity between 150 l and 3000 l - Design, construction and testing (ISO 11120:2015) |
EN 720-2 : 1996 | TRANSPORTABLE GAS CYLINDERS - GASES AND GAS MIXTURES - PART 2: DETERMINATION OF FLAMMABILITY AND OXIDIZING ABILITY OF GASES AND GAS MIXTURES |
ISO 2884-1:1999 | Paints and varnishes — Determination of viscosity using rotary viscometers — Part 1: Cone-and-plate viscometer operated at a high rate of shear |
EN 1964-1:1999/AC:1999 | TRANSPORTABLE GAS CYLINDERS - SPECIFICATION FOR THE DESIGN AND CONSTRUCTION OF REFILLABLE TRANSPORTABLE SEAMLESS STEEL GAS CYLINDERS OF WATER CAPACITIES FROM 0.5 LITRE UP TO AND INCLUDING 150 LITRES - PART 1: CYLINDERS MADE OF SEAMLESS STEEL WITH AN RM VALUE OF LESS THAN 1100 MPA |
EN 12862:2000 | Transportable gas cylinders - Specification for the design and construction of refillable transportable welded aluminium alloy gas cylinders |
EN 1964-3:2000 | Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and including 150 litres - Part 3: Cylinders made of seamless stainless steel with an Rm value of less than 1100 MPa |
ISO 3341:2000 | Textile glass Yarns Determination of breaking force and breaking elongation |
ISO 13341:2010 | Gas cylinders — Fitting of valves to gas cylinders |
EN ISO 11114-3:2010 | Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 3: Autogenous ignition test for non-metallic materials in oxygen atmosphere (ISO 11114-3:2010) |
EN ISO 13769:2009 | Gas cylinders - Stamp marking (ISO 13769:2007) |
ISO 11114-3:2010 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 3: Autogenous ignition test for non-metallic materials in oxygen atmosphere |
ISO 1628-3:2010 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 3: Polyethylenes and polypropylenes |
ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
ISO 10618:2004 | Carbon fibre — Determination of tensile properties of resin-impregnated yarn |
EN 1964-2 : 2001 | TRANSPORTABLE GAS CYLINDERS - SPECIFICATION FOR THE DESIGN AND CONSTRUCTION OF REFILLABLE TRANSPORTABLE SEAMLESS STEEL GAS CYLINDERS OF WATER CAPACITIES FROM 0,5 LITRE UP TO AND INCLUDING 150 LITRES - PART 2: CYLINDERS MADE OF SEAMLESS STEEL WITH AN R[M] VALUE OF 1 100 MPA AND ABOVE |
ISO 11114-2:2013 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials |
ISO 11120:2015 | Gas cylinders Refillable seamless steel tubes of water capacity between 150 l and 3000 l Design, construction and testing |
ISO 3146:2000 | Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
EN 1800:2006 | Transportable gas cylinders - Acetylene cylinders - Basic requirements, definitions and type testing |
ISO 11623:2015 | Gas cylinders — Composite construction — Periodic inspection and testing |
EN 962:1996/A2:2000 | TRANSPORTABLE GAS CYLINDERS - VALVE PROTECTION CAPS AND VALVE GUARDS FOR INDUSTRIAL AND MEDICAL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTS |
ISO 10156:2017 | Gas cylinders — Gases and gas mixtures — Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets |
EN ISO 11114-2:2013 | Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013) |
EN 1089-3:2011 | Transportable gas cylinders - Gas cylinder identification (excluding LPG) - Part 3: Colour coding |
EN 3-1 : 1996 | PORTABLE FIRE EXTINGUISHERS - PART 1: DESCRIPTION, DURATION OF OPERATION, CLASS A AND B FIRE TEST |
ISO 11114-4:2017 | Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 4: Test methods for selecting steels resistant to hydrogen embrittlement |
ISO 15512:2016 | Plastics Determination of water content |
EN 14427:2014 | LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction |
ASTM D 2290 : 2016-12 | TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE |
ASTM D 4018 : 2017 : REDLINE | Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows |
EN ISO 11623:2015 | Gas cylinders - Composite construction - Periodic inspection and testing (ISO 11623:2015, Corrected version 2017-02) |
ISO 14130:1997 | Fibre-reinforced plastic composites — Determination of apparent interlaminar shear strength by short-beam method |
ISO 75-3:2004 | Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
EN 12257:2002 | Transportable gas cylinders - Seamless, hoop-wrapped composite cylinders |
EN 1089-2 : 2002 | TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - PART 2: PRECAUTIONARY LABELS |
ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
EN 14638-1:2006 | Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 1: Welded austenitic stainless steel cylinders made to a design justified by experimental methods |
ISO 13769:2007 | Gas cylinders Stamp marking |
ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
EN ISO 11439:2013 | Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013) |
ISO 11439:2013 | Gas cylinders — High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
EN 629-1 : 1996 | TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - PART 1: SPECIFICATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.