I.S. EN 13445-6:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON
Hardcopy , PDF
30-11-2021
27-09-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms, definitions, units and symbols
4 Service conditions
5 Requirements
6 Material testing
7 Testing and final assessment
8 Pressure vessels constructed of a combination of parts in different materials
9 Marking and documentation
Annex A (normative) Technical data for the design calculations
Annex B (informative) Ductility
Annex C (informative) Determination of the minimum local wall thickness and minimum required burst test pressure
Annex D (normative) Assessment of fatigue life
Annex E (normative) Design by analysis for castings
Annex F (informative) Recommandations for in-service validation and inspection
Annex G (normative) Specific design requirements
Annex H (normative) Experimental cyclic pressure testing procedure
Annex Y (informative) History of EN 13445-6
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of the EU Pressure Equipment Directive 97/23/EC
Bibliography
This European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than 100 bar and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron.
| Committee |
TC 54
|
| DevelopmentNote |
ISSUE 3 dated 19.08.2016 issued incorporating latest Correction Notice issued by CEN dated 03.08.2016. (09/2016)
|
| DocumentType |
Standard
|
| Pages |
62
|
| ProductNote |
Consolidated version for this standard is available on Jan,2019,Incorporating amendments/corrigenda/National Annexes issued since publication: EN 13445-6:2014/A1:2015 EN 13445-6:2014/A2:2018 The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. THIS STANDARD ALSO REFERS TO EN 764-5:2002,EN 837-1:1996,EN 13445-1:2014,EN 13835:2002,EN ISO 945-1:2008,EN ISO 8062-1:2007,ISO/CD 1083,SFS 3320
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 13445-6 : 2014 COR 2017 | Identical |
| NS EN 13445-6 : 2014 AMD 1 2015 | Identical |
| EN 13445-6:2014/A2:2018 | Identical |
| SN EN 13445-6 : 2014 AMD 1 2016 | Identical |
| NEN EN 13445-6 : 2016 | Identical |
| UNI EN 13445-6 : 2015 | Identical |
| BS EN 13445-6 : 2014 | Identical |
| NF EN 13445-6 : 2014 AMD 1 2015 | Identical |
| EN 13445-6:2014 | Identical |
| NBN EN 13445-6 : 2014 AMD 1 2015 | Identical |
| ONORM EN 13445-6 : 2017 | Identical |
| DIN EN 13445-6:2015-12 | Identical |
| UNE-EN 13445-6:2015 | Identical |
| I.S. 328:2015/AC1:2015 | GAS TRANSMISSION PIPELINES AND PIPELINE INSTALLATIONS (EDITION 4) |
| I.S. 328:2015 | GAS TRANSMISSION PIPELINES AND PIPELINE INSTALLATIONS (EDITION 4) |
| EN ISO 8062-1:2007 | Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 1: Vocabulary (ISO 8062-1:2007) |
| EN ISO 8062-3 : 2007 COR 2009 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 3: GENERAL DIMENSIONAL AND GEOMETRICAL TOLERANCES AND MACHINING ALLOWANCES FOR CASTINGS |
| EN 13445-5 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING |
| EN 1559-3:2011 | Founding - Technical conditions of delivery - Part 3: Additional requirements for iron castings |
| ISO 15614-3:2008 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 3: Fusion welding of non-alloyed and low-alloyed cast irons |
| EN 13445-5:2014 | Unfired pressure vessels - Part 5: Inspection and testing |
| ISO 1083:2004 | Spheroidal graphite cast irons - Classification |
| ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings |
| EN 13068-2:1999 | Non-destructive testing - Radioscopic testing - Part 2: Check of long term stability of imaging devices |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| EN 13835:2012 | Founding - Austenitic cast irons |
| ISO 3320:2013 | Fluid power systems and components — Cylinder bores and piston rod diameters and area ratios — Metric series |
| EN 1370:2011 | Founding - Examination of surface condition |
| ISO 12107:2003 | Metallic materials Fatigue testing Statistical planning and analysis of data |
| ISO 8062-1:2007 | Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 1: Vocabulary |
| EN 1371-1:2011 | Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| EN 12680-3:2011 | Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 1369:2012 | Founding - Magnetic particle testing |
| EN 12681:2003 | Founding - Radiographic examination |
| EN 764-2:2012 | Pressure equipment - Part 2: Quantities, symbols and units |
| EN 837-3:1996 | Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing |
| ISO 12107:2012 | Metallic materials — Fatigue testing — Statistical planning and analysis of data |
| ISO 945-1:2008 | Microstructure of cast irons Part 1: Graphite classification by visual analysis |
| EN ISO 15614-3:2008 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 3: Fusion welding of non-alloyed and low-alloyed cast irons (ISO 15614-3:2008) |
| EN 15776:2011+A1:2015 | Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 % |
| EN 13068-1:1999 | Non-destructive testing - Radioscopic testing - Part 1: Quantitative measurement of imaging properties |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.