Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 13617-4:2012

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS

    Available format(s):  Hardcopy, PDF

    Superseded date:  09-10-2021

    Language(s):  English

    Published date:  01-01-2012

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Explosion protection measures
    5 Construction
    6 Physical properties
    7 Functional requirements
    8 Frequency of testing
    9 Information for use
    Annex A (normative) - Testing
    Annex B (informative) - Environmental aspects
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 94/9/EC

    Abstract - (Show below) - (Hide below)

    Describes safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min[-1].

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1127-1:2011 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
    EN 228:2012+A1:2017 Automotive fuels - Unleaded petrol - Requirements and test methods
    ISO 1825:2010 Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling Specification
    EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
    EN 13617-2:2012 Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
    EN 13483:2013 Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
    EN 13463-1:2009 Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements
    EN ISO 8031:2009 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009)
    ISO 965-2:1998 ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
    EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
    ISO 11925-3:1997 Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 3: Multi-source test
    ISO 261:1998 ISO general purpose metric screw threads General plan
    EN 13012:2012 Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers
    EN 1360:2013 Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
    PREN 13617-1 : DRAFT 2010 PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective