I.S. EN 14636-2:2009
Current
The latest, up-to-date edition.
PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
Hardcopy , PDF
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 General requirements
5 Manholes and inspection chamber units
6 Dangerous substances
7 Manufacturer's installation recommendations
8 Evaluation of conformity
Annex A (normative) - Determination of a chamber ring's or
shaft ring's crushing strength and
ring bending tensile strength using
a ring test piece
Annex B (normative) - Test method for the determination of a
chamber ring's or shaft ring's crushing
strength or the ring bending tensile
strength using test pieces sawn from a
ring
Annex C (normative) - Test method for the determination of
the vertical crushing strength of slabs
or tapers
Annex D (normative) - Test method for the determination of the
compressive strength of polyester resin
Annex E (normative) - Test method for the determination of the
resistance of installed steps to vertical
and horizontal loading
Annex F (normative) - Method for the assessment of the leak-tightness
of a manhole or inspection chamber and its
joints under short term exposure to internal
water pressure and negative pressure
Annex G (normative) - Test method for the determination of the
long-term crushing strength (50 years
evaluation point) of a chamber ring or a
shaft ring, including the effects of media
attack
Bibliography
Describes units made from polyester resin concrete, and their joints, for the construction of inspection chambers with inverts not exceeding 2 m deep and for manholes, intended to be used within a drain or sewer system operating without pressure.
| DocumentType |
Standard
|
| Pages |
62
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 14636-2:2009 | Identical |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 13121-1:2003 | GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance conditions |
| EN 14636-1:2009 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN 476:2011 | General requirements for components used in drains and sewers |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 13101:2002 | Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity |
| ISO 9001:2015 | Quality management systems — Requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.