I.S. EN 14753:2007

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
  5.1 General
      5.1.1 Introduction
      5.1.2 CCM-arrangement, site inspection
      5.1.3 Safety layout
      5.1.4 Safety devices
      5.1.5 Hydraulic, pneumatic, gas, cooling and lubrication
            systems
      5.1.6 Fluid systems carrying or containing fluids
      5.1.7 Fluids to be discharged to drains
      5.1.8 Personal protective equipment
      5.1.9 Warning devices and safety signs
      5.1.10 Access
      5.1.11 Escape ways
      5.1.12 Electrical equipment
      5.1.13 Safety control system
      5.1.14 Surface temperatures and heat radiation
      5.1.15 Ergonomic principles
      5.1.16 Fire protection
      5.1.17 Operating positions of the CCM
      5.1.18 Movable control box
      5.1.19 Loss of energy
      5.1.20 Harmful areas
      5.1.21 Cooling water systems
      5.1.22 Radioactive sources
      5.1.23 Ladle/tundish emergency systems
      5.1.24 Shroud manipulators
      5.1.25 Cooling chamber
  5.2 List of significant hazards, hazardous situations, safety
      requirements and/or measures
      5.2.1 General
      5.2.2 General
      5.2.3 Casting platform
      5.2.4 Casting machine equipment
      5.2.5 Cutting systems
      5.2.6 Run-out (discharge) area
  5.3 Special safety requirements or measures
      5.3.1 General
      5.3.2 Hold-to-run control device
      5.3.3 Mechanical restraint devices
      5.3.4 Accessible rotating/moving parts
  5.4 Noise reduction as a safety requirement
      5.4.1 Noise sources
      5.4.2 Noise reduction at source by design
      5.4.3 Noise reduction by protective measures
      5.4.4 Noise reduction by information
6 Verification of the safety requirements and/or measures
7 Information for use
  7.1 Signs and warning devices
  7.2 Accompanying documents
      7.2.1 Instruction handbook
      7.2.2 Machine/equipment declaration
      7.2.3 Instruction for transport, setting up/installation
      7.2.4 Information about commissioning and dismantling
      7.2.5 Operation instructions concerning the equipment
      7.2.6 Maintenance manual
  7.3 Minimum marking
  7.4 Training of personnel
Annex A (normative) Safety requirements and/or measures for
        electrical equipment and controls
      A.1 General
      A.2 Special requirements for controls
      A.3 Special requirements for shut-down equipment
          A.3.1 Stop and emergency-off functions
          A.3.2 Emergency stops
          A.3.3 Emergency stop functions
          A.3.4 Emergency stop assigned to areas
Annex B (normative) Equipment of a CCM covered by this standard
      B.1 Casting platform
      B.2 Casting machine equipment
      B.3 Cutting area
      B.4 Run-out (discharge) area
      B.5 General equipment
Annex C (normative) Noise test code
      C.1 Introduction
      C.2 Determination of sound power level
      C.3 Determination of emission sound pressure levels
          C.3.1 Determination of the emission sound pressure level
                at specified measuring points
          C.3.2 Determination of emission sound pressure level at
                work stations
      C.4 Measurement uncertainty
      C.5 Operating conditions
      C.6 Information to be recorded and reported
      C.7 Declaration and verification of noise emission values
Annex ZA (informative) Relationship between this European Standard
         and the Essential Requirements of EU Directive 98/37/EC
Annex ZB (informative) Relationship between this European Standard
         and the Essential Requirements of EU Directive 2006/42/EC
Bibliography

Defines the safety requirements to be met during design, assembly, transport, commissioning, operation, maintenance and decommissioning of the equipment.