Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 15383:2012

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

    PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS

    Available format(s):  Hardcopy, PDF

    Withdrawn date:  23-10-2013

    Language(s):  English

    Published date:  11-01-2013

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
    4 General requirements
    5 Geometrical characteristics
    6 Mechanical characteristics
    7 Leak-tightness of manholes and inspection chambers and
       their joints
    8 Minimum required marking
    9 Ancillary products
    10 Dangerous substances
    11 Manufacturer's installation recommendations
    12 Evaluation of conformity
    Annex A (normative) - Determination of the longitudinal
            compressive properties measured on prism shaped test
            pieces
    Annex B (normative) - Determination of the resistance of
            installed steps to vertical or horizontal loading

    Abstract - (Show below) - (Hide below)

    Pertains to a) manholes, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); b) inspection chambers, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) which are intended to be used with inverts which are at a depth not exceeding 2 m.

    General Product Information - (Show below) - (Hide below)

    Development Note 2012 Edition Re-Issued in October 2013 & incorporates AMD 1 2013. (10/2013)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Withdrawn

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
    EN 14396:2004 Fixed ladders for manholes
    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    EN ISO 604 : 2003 PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES (ISO 604:2002)
    CEN/TS 14632:2012 Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
    EN 1917:2002/AC:2008 CONCRETE MANHOLES AND INSPECTION CHAMBERS, UNREINFORCED, STEEL FIBRE AND REINFORCED
    ISO 2602:1980 Statistical interpretation of test results Estimation of the mean Confidence interval
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    EN 476:2011 General requirements for components used in drains and sewers
    ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints
    EN 124:1994 Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control
    ISO 604:2002 Plastics — Determination of compressive properties
    EN 13101:2002 Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity
    EN 1119:2009 Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements
    EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective