I.S. EN 1555-2:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES
Hardcopy , PDF
English
01-01-2010
17-12-2021
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical characteristics
9 Performance requirements
10 Marking
Annex A (normative) - Pipes with co-extruded layers
Annex B (normative) - Pipes with peelable layer
Annex C (normative) - Squeeze-off technique
Bibliography
National Annex Foreword
Annex NA (informative) - Irish National Annex to
I.S. EN 1555-2:2010 - Plastics piping
systems for the supply of gaseous
fuels - Polyethylene (PE) - Part 2: Pipes
NA.1 Introduction
NA.2 Scope
NA.3 Normative references
NA.4 Base compound colour of peelable pipe
NA.5 Compound colour for PE pipe (non-peelable)
Describes the characteristics of pipes made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
| DevelopmentNote |
Now includes Irish National Annex 2015 which is also available as a separate document, See I.S. EN 1555-2 NATIONAL ANNEX. (05/2015)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN 1555-2 : 2010 | Identical |
| NS EN 1555-2 : 1ED 2010 | Identical |
| EN 1555-2:2010 | Identical |
| NBN EN 1555-2 : 2010 | Identical |
| BS EN 1555-2:2010 | Identical |
| DIN EN 1555-2:2010-12 | Identical |
| NF EN 1555-2 : 2010 | Identical |
| ONORM EN 1555-2 : 2011 | Identical |
| UNE-EN 1555-2:2011 | Identical |
| I.S. 820:2010 | NON-DOMESTIC GAS INSTALLATIONS |
| I.S. 813:2014+A1:2017 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| I.S. EN 1555-2 NATIONAL ANNEX:2015 | NATIONAL ANNEX TO I.S. EN 1555-2:2010 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| I.S. EN 1555-1:2010-2015 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| I.S. 813:2014 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| I.S. EN 1555-1 NATIONAL ANNEX:2015 | NATIONAL ANNEX TO I.S. EN 1555-1:2010 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| ISO 17484-1:2014 | Plastics piping systems — Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) — Part 1: Specifications for systems |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 12106:1997 | Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| BS 5252:1976 | Framework for colour co-ordination for building purposes |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 13968:2008 | Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| EN ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008) |
| ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| EN ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007) |
| EN ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids - Determination of resistance to crack propagation - Test method for slow crack growth on notched pipes (ISO 13479:2009) |
| CEN/TR 15438:2007 | Plastics piping systems - Guidance for coding of products and their intended uses |
| I.S. EN 1555-1:2010-2015 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| ISO 6259-1:2015 | Thermoplastics pipes — Determination of tensile properties — Part 1: General test method |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| EN ISO 13968:2008 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility (ISO 13968:2008) |
| PREN 1555-4 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| ISO 11357-6:2008 | Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 4065:1996 | Thermoplastics pipes — Universal wall thickness table |
| ISO 13480:1997 | Polyethylene pipes — Resistance to slow crack growth — Cone test method |
| ISO 18225:2012 | Plastics piping systems — Multilayer piping systems for outdoor gas installations — Specifications for systems |
| CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| ISO 6259-3:2015 | Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 9969:2016 | Thermoplastics pipes — Determination of ring stiffness |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.