I.S. EN 1555-4:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES
Hardcopy , PDF
English
01-01-2011
17-12-2021
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics of assembled valves
8 Physical characteristics
9 Performance requirements
10 Marking
11 Delivery conditions
Annex A (normative) - Determination of the leaktightness
of seat and packing
Bibliography
Describes the characteristics of valves made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 1555-4:2011 | Identical |
| NBN EN 1555-4 : 2011 | Identical |
| NEN EN 1555-4 : 2011 | Identical |
| DIN EN 1555-4:2011-07 | Identical |
| BS EN 1555-4:2011 | Identical |
| NF EN 1555-4 : 2011 | Identical |
| NS EN 1555-4 : 2011 | Identical |
| ONORM EN 1555-4 : 2011 | Identical |
| UNE-EN 1555-4:2011 | Identical |
| I.S. 820:2010 | NON-DOMESTIC GAS INSTALLATIONS |
| I.S. 813:2014+A1:2017 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| I.S. 813:2014 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| ISO 8233:1988 | Thermoplastics valves — Torque — Test method |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 1705:1996 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| ISO 5210:2017 | Industrial valves — Multi-turn valve actuator attachments |
| EN ISO 5210:2017 | Industrial valves - Multi-turn valve actuator attachments (ISO 5210:2017) |
| EN 28233:1990 | Thermoplastics valves - Torque - Test method (ISO 8233:1988) |
| EN 12119:1997 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 4: Preparation of assemblies |
| EN 1704:1997 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after temperature cycling under bending |
| EN 12100:1997 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| EN 736-2:2016 | Valves - Terminology - Part 2: Definition of components of valves |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| EN ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
| EN 1680:1997 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms |
| ISO 10933:1997 | Polyethylene (PE) valves for gas distribution systems |
| EN 744:1995 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| ISO 11357-6:2008 | Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN 12117:1997 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN 736-3:2008 | Valves - Terminology - Part 3: Definition of terms |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.