I.S. EN 15776:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM CAST IRON WITH AN ELONGATION AFTER FRACTURE EQUAL OR LESS THAN 15%
Hardcopy , PDF
02-02-2022
English
23-02-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, units and symbols
4 Materials, limitations and service conditions
5 Design requirements
6 Founding, material and casting testing
7 Final assessment
8 Pressure vessels assembled of a combination of parts in
different materials
9 Marking and documentation
Annex A (normative) - Technical data for design calculations
Annex B (informative) - Recommendations for in-service
validation and inspection
Annex C (informative) - Examples of fatigue design curves
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 97/23/EC
Bibliography
Defines requirements for the design, material, manufacturing and testing of pressure vessels and pressure vessel parts made from materials for which details are specified from the following material standards for specific grades which meet the criterion of an elongation after fracture less than or equal to 15%: - EN 1561:2011, Founding - Grey cast irons; - EN 1563:2011, Founding - Spheroidal graphite cast irons; - EN 13835:2012, Founding - Austenitic cast irons.
| DevelopmentNote |
2011 Edition Re-Issued in November 2015 & incorporates AMD 1 2015. 2011 Edition Incorporates Corrigendum. (11/2015)
|
| DocumentType |
Standard
|
| Pages |
43
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 15776:2011+A1:2015 | Identical |
| EN ISO 8062-3 : 2007 COR 2009 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 3: GENERAL DIMENSIONAL AND GEOMETRICAL TOLERANCES AND MACHINING ALLOWANCES FOR CASTINGS |
| EN 13445-5 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING |
| EN 1559-3:2011 | Founding - Technical conditions of delivery - Part 3: Additional requirements for iron castings |
| EN 13445-6 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| EN 13835:2012 | Founding - Austenitic cast irons |
| EN 1370:2011 | Founding - Examination of surface condition |
| EN 1371-1:2011 | Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 12680-3:2011 | Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 1369:2012 | Founding - Magnetic particle testing |
| EN 12681:2003 | Founding - Radiographic examination |
| ISO 185:2005 | Grey cast irons Classification |
| EN 764-2:2012 | Pressure equipment - Part 2: Quantities, symbols and units |
| EN 837-3:1996 | Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing |
| ISO 945-1:2008 | Microstructure of cast irons Part 1: Graphite classification by visual analysis |
| EN 1561:2011 | Founding - Grey cast irons |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.