I.S. EN 15895:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CARTRIDGE OPERATED HAND-HELD TOOLS - SAFETY REQUIREMENTS - FIXING AND HARD MARKING TOOLS
Hardcopy , PDF
English
30-05-2011
23-01-2025
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of the safety requirements and/or protective
measures
7 Information for use
Annex A (normative) - Values of combustion equation for
the calculation of maximum gas pressure in the
cartridge chamber [pmax] according to 3.15
Annex B (informative) - Example of testing procedures for
determination of muzzle velocity
Annex C (normative) - Testing for the verification of safe
operation
Annex D (normative) - Noise test code
Annex E (informative) - Information on the ergonomic design
of the handle
Annex F (normative) - Essential safety dimensions
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
Describes safety requirements for cartridge operated fixing and hard marking tools which operate with an intermediate member (piston).
| DevelopmentNote |
2011 Edition Re-Issued in June 2018 & incorporates AMD 1 2018. (06/2018)
|
| DocumentType |
Standard
|
| Pages |
51
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 15895:2011+A1:2018 | Identical |
| EN 15895:2011 | Equivalent |
| DIN EN 15895:2011-08 | Equivalent |
| BS EN 15895 : 2011 | Equivalent |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for an essentially free field over a reflecting plane |
| ISO/TR 11688-1:1995 | Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning |
| ISO 7250:1996 | Basic human body measurements for technological design |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| ISO 11690-2:1996 | Acoustics — Recommended practice for the design of low-noise workplaces containing machinery — Part 2: Noise control measures |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 792-13:2000+A1:2008 | Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools |
| EN ISO/TS 15694 : 2004 | MECHANICAL VIBRATION AND SHOCK - MEASUREMENT AND EVALUATION OF SINGLE SHOCKS TRANSMITTED FROM HAND-HELD AND HAND-GUIDED MACHINES TO THE HAND-ARM SYSTEM |
| EN ISO 11690-2:1996 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 2: Noise control measures (ISO 11690-2:1996) |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 7250 : 1997 | BASIC HUMAN BODY MEASUREMENTS FOR TECHNOLOGICAL DESIGN |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| ISO 11201:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO/TS 15694:2004 | Mechanical vibration and shock — Measurement and evaluation of single shocks transmitted from hand-held and hand-guided machines to the hand-arm system |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.